Abstract:Innovation in comminution is expected to continue unabated to address the inefficiencies that are inherent in comminution circuits. The rotary offset crusher (ROC) is a new comminution device with a promising performance potential in terms of throughput due to the enhanced speed of transportation induced by the centrifugal force of the discs. However, the processes driving the comminution of particles trapped in the conical space between the two discs of the crusher are not fully understood. To gain a better insight into the comminution process in this device, discrete element modeling (DEM) simulations were conducted to study the breakage of a single particle for the crusher operated under two different dynamic conditions, i.e., (1) a stationary top disc and (2) both discs rotating at the same speed. For both scenarios, the speed of the discs was varied between 550 and 2350 rpm. Experimental testwork was also conducted with the laboratory prototype to generate the data that were used to calibrate the breakage parameters of the Ab × t10 breakage model. Simulations were performed using polyhedral UG2 ore particles that were generated with the in-built particle generator in the DEM simulator. The simulated ROC, which is operated with both discs rotating, outperformed the ROC with a stationary top disc in terms of the specific input energy and throughput. The crusher with a stationary top disc is characterized by high shear forces (suggesting a higher wear rate), specific input energies greater than 1 kWh/t, and low throughputs (<50 kg/h). The ROC operated with a stationary disc is not recommended for hard rock applications due to expected excessive wear of crushing surfaces and higher energy consumption. The freewheeling discs are recommended, but there is scope to optimize the crusher performance in terms of the power draw, size reduction, and throughput by manipulating the difference between the speeds of the discs. There is also scope to optimize the crusher performance when it is simulated with many particles. Once the full performance potential of the ROC is established, it will then be important to benchmark it against the existing crushers in the minerals industry as well as other industries where crushers are used.

Research on discrete element parameter calibration of ore particles based on Tavares breakage model in a SAG mill

Dem Investigation Of Sag Mill With Spherical Grinding Media And Non-Spherical Ore Based On Polyhedron-Sphere Contact Model

DEM Simulation of an Impact Crusher Using the Fast-Cutting Breakage Model

Investigation of the Effect of Filling Level on the Wear and Vibration of a SAG Mill by DEM

Measurement and Simulation Validation of DEM Parameters of Pellet, Sinter and Coke Particles

Investigation of Modeling Non-Spherical Particles by Using Spherical Discrete Element Model with Rolling Friction

Operation Analysis of a SAG Mill under Different Conditions Based on DEM and Breakage Energy Method

Determining Digital Representation and Representative Elementary Volume Size of Broken Rock Mass Using the Discrete Fracture Network–Discrete Element Method Coupling Technique

Discrete element modeling and simulation of non-spherical particles using polyhedrons and super-ellipsoids

Numerical Prediction of Wear in SAG Mills Based on DEM Simulations

A Comparative Study of the Performance of Different Particle Models in Simulating Particle Charging and Burden Distribution in a Blast Furnace Within the DEM Framework

Numerical Investigation of a Vertical Roller Mill Using DEM-MBD Coupling Method

Discrete-element simulation of particle breakage inside ball mills: A 2D model

Investigation of the Ball Wear in a Planetary Mill by DEM Simulation

Modelling of dry milling in planetary ball mill through discrete element method

Discrete Element Modeling of the Breakage of Single Polyhedral Particles in the Rotary Offset Crusher

Study on the Particle Breakage of Ballast Based on a GPU Accelerated Discrete Element Method

3D modelling of soil-rock mixtures considering the morphology and fracture characteristics of breakable blocks

DEM study on the microscale and macroscale shear behaviours of granular materials with breakable and irregularly shaped particles

Application of Multibody Dynamics and Bonded-Particle GPU Discrete Element Method in Modelling of a Gyratory Crusher

A coupled FEM-DEM study on mechanical behaviors of granular soils considering particle breakage