Abstract:Water-based lubrication faces the common challenge of component lifetime extension which is impaired by tribocorrosion due to material surface depassivation. However, such mechanisms in a pH-neutral and low-halide electrolyte require additional understanding. A ball-on-flat configuration study of hard-phase materials in a low amplitude–high frequency sliding contact against martensitic chromium steel with contact pressures around 200 MPa is presented. Under lubrication by purified water, tungsten carbide-based metal matrix composite (MMC) with NiCr binder and silicon nitride-based ceramic (SiAlON) against DIN/EN 1.4108 steel yielded coefficients of friction above unity. Wear scar enlargement led to fretting-like conditions with adhesion becoming the fundamental wear mechanism. A tribocorrosion-induced depletion of tungsten carbide and nickel was determined for MMC. SiAlON materials suffered extreme wear under the formation of abrasive SiO2, while heat-treated DIN/EN 1.4125 steel showed lower friction and wear, but also showed signs of hydrogen embrittlement. Results from accompanying single-material corrosion experiments could not satisfactorily explain the phenomena. Including galvanic interaction and the influence of contact geometry, a new tribocorrosion model for fretting conditions is proposed. It describes an expanding anodic belt located at the inner-most crevice position of an otherwise cathodically polarized material. Low conductivity of the electrolyte is seen as a key player in this process, while the galvanic situation between two materials in contact was shown to invert when water was substituted by a wet organic phase.

Evolution of Wetted and Corroded Areas on 8cr4mo4v Bearing Steel Exposed to Salt Water Contaminated Lubricant Oil

Droplet size dependent localized corrosion evolution of M50 bearing steel in salt water contaminated lubricant oil

Investigation of the Corrosion–Wear Interaction Behavior of 8Cr4Mo4V Bearing Steel at Various Corrosion Intervals

Spontaneous process of dispersed salt water droplets in lubricant oil establishing wetted areas: Settling, spreading, coalescing and de-wetting

Investigation on Corrosion–Wear Interaction Behavior of 8Cr4Mo4V-Bearing Steel Under Various Operating Conditions

Study on Corrosion Behavior and First-Principle Analysis of M50 Steel in Lubricating Oil Contaminated by Salt Water

Study of the Corrosion Behaviors of M50 Steel in Brine-Contaminated Lubricating Oil

Corrosion Development of Carbon Steel Grids and Shear Connectors in Cracked Composite Beams Exposed to Wet-Dry Cycles in Chloride Environment.

A Corrosion Cracking Mechanism-Based Model with Molten Salt Corrosion Damage Coupling the Effect of Chloride Impurity and Plastic Deformation

Corrosion Assessment and Characterization of Aerospace-Bearing Steels in Seawater and Ester-Based Lubricants

CORROSION BEHAVIOR OF SUPER-AUSTENITIC STAINLESS STEEL AL-6XN IN SUPERCRITICAL WATER

Molecular Dynamics Simulation of Reinforcing Steel Corrosion when Subjected to Both Chloride Attack and Mechanical Loading

Wide temperature range corrosion mechanism of M50 bearing steel in deteriorated oil-water mixture

Mechanical and surface characterization of interstitial‐free steel corroded under wet‐dry salt spray and immersion conditions: A comparative study

Corrosion and Wear Behavior of WC–10Co4Cr Coating under Saturated Salt Drilling Fluid

Correlating numerical modelling with experimental studies to quantify the wear resistance of high-carbon chromium bearing steel in mixed lubrication

A Study on Decisive Early Stages in White Etching Crack Formation Induced by Lubrication

Tribocorrosive Aspects of Tungsten Carbide, Silicon Nitride, and Martensitic Steel under Fretting-like Conditions

Tribocorrosion Behavior of Several Corrosion-resistant Alloys Sliding Against CF-PEEK: Application for Hydraulic Valve in Seawater

Corrosion Behavior and Mechanism of WC-12Co Coating in Salt Spray Environment

Interaction Between Erosive-Wear and Corrosion of Alloy Materials for Hydroturbine in Hydroelectric Station