Abstract:The hot corrosion behaviour of plasma sprayed WC-CoCr coatings on AISI 316L steel substrate is studied in two corrosive salt environments namely 100% Na2SO4 and 75% Na2SO4+25%NaCl at 1000 °C. Also, on WC-CoCr coated AISI 316L steel substrate, a persistent Cr2O3 barrier scale is created employing pre-oxidation at 1200 °C for ten hours with the expectation that it would withstand hot corrosion in a Na2SO4 salt environment at 900 °C. X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), electron micro probe analysis (EPMA) and scanning electron microscopy (SEM) are performed on samples to examine the pre oxidation and hot corrosion characteristics of plasma sprayed WC-CoCr coatings at elevated temperatures. The findings indicate that the presence of both salt environment affects the degradation process of WC-CoCr coatings. The coatings in 100% Na2SO4 and the mixture of 75% Na2SO4+25%NaCl has a weight change of 0.14 mg/cm2 and 0.33 mg/cm2, respectively, after hot corrosion at 1000 °C for 50 cycles. Each cycle includes 1 hour heating in furnace and 20 minutes cooling in ambient air. Corrosion kinetics using thermogravimetric method showed that non-pre-oxidized samples gained 52.5 % more weight and more severely affected by hot corrosion than pre-oxidized ones. During hot corrosion after 2 hours, there was relatively negligible corrosion, but after 4 and 8 hours, deposits of Na2WO4, WO3, Cr2O3 and CoSO4 were produced. Oxides were primarily composed of Cr2O3 and WO3. Cr2O3 and WO3 acted as barriers to the penetration and diffusion of corrosive elements through coatings, which contributed to the hot corrosion resistance in the corrosive area. The hot corrosion deterioration of WC-CoCr coatings may be effectively reduced by introducing pre oxidation. Slower reaction rate of pre oxidized Cr2O3 scale may operate as a barrier which separates hot corrosion by Na2SO4 salt.

Corrosion Behavior and Mechanism of WC-12Co Coating in Salt Spray Environment

Microstructure and Corrosion Behaviour of WC-Co Coating Fabricated by Plasma Arc Welding

Corrosion and Wear Behavior of WC–10Co4Cr Coating under Saturated Salt Drilling Fluid

HVOF Spray Performance Optimization Analysis and Experimental Research of WC–12Co Coating on Ti Alloy

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Oxidation corrosion wear and lubricating mechanisms of WC particles reinforced FeCoCrNiMn high - entropy alloys coatings

The corrosion performance for ultrafine WC-12Co processed by heat treatments in different pH solution

Preparation of WC/Co Powders by Electroless Plating and Its Coating on 2cr13 Stainless Steel by Laser Cladding

Electrochemical corrosion behavior variation of WC-10Co4Cr coating subjected to different magnetic treatments and its mechanism

Corrosion of the WC-12Co and enamel coatings in liquid Zn-55Al alloy at 640 °C

Comparison on Long-Term Corrosion Performance of WC-CoCr and Al2O3-TiO2 Ceramic Coatings in Sulphide-Containing 3.5 Wt% NaCl Solution

Surface morphological studies on hot corrosion behaviour of pre-oxidized plasma sprayed WC-CoCr coating on AISI316L steel in Na 2 SO 4 /NaCl molten salt environment

Effect of the microstructure of corrosion products on tribo-corrosion performance of HVOF-sprayed NiCrWMoCuCBFe coating

Corrosion and wear resistant WC17Co-TC4 composite coatings with fully dense microstructure enabled by in-situ forging of the large-sized WC17Co particles in cold spray

Tribocorrosion behavior of HVOF sprayed WC-based cermet coatings in sodium chloride solution environment in relation to binder phases

Influence of Heat Treatment on Corrosion Resistance of High-Velocity Oxygen-Fuel Sprayed WC-17Co Coatings on 42CrMo Steel

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying

Wear performance of the plasma sprayed fine WC-Co composite powders coatings

The influence of sulphide on the ultrasonic cavitation erosion-corrosion behaviors of HVOF-sprayed WC-Cr 3 C 2 -Ni coating

Effects of WC on the Microstructure, Wear and Corrosion Resistance of Laser-Deposited CoCrFeNi High Entropy Alloy Coatings

Effect of WC-10Co-4Cr Reinforcement Amount on Wear and Corrosion Resistance of Fe-Based Amorphous Coatings