Abstract:It is irrefutable that the presence of hydrogen reduces the mechanical performance of many metals and alloys used for structural components. Several mechanisms of hydrogen-assisted cracking (HAC) of steels have been postulated. The direct evidence of the mechanisms by which hydrogen embrittles these materials has remained elusive. This is by virtue of our difficulty to directly observe the hydrogen distribution at spatial resolutions less than 100 nm and analysis volumes greater than 1 × 109 atoms at microstructural features such as grain boundaries, dislocations, twins, stacking faults and sub-micron inclusions that are all potential hydrogen trapping sites postulated to be responsible for the degradation of mechanical performance. Here, we report on an experimental methodology combining an elaborate fatigue testing protocol in an enriched gaseous deuterium environment with NanoSIMS (secondary ion mass spectrometry) imaging for detection of deuterium at spatial resolutions as low as 100 nm and accompanying TEM analysis. Type 316 stainless steel compact tension specimens were precharged in deuterium followed by fatigue testing at high stress ratio (0.7), low delta K (~11 MPa √m), and a frequency of 1 cycle per minute using a sawtooth waveform with a rise time of 30 s in high pressure (68.9 MPa) gaseous deuterium (99.999% purity) environment at room temperature. High resolution NanoSIMS imaging was then used to measure the deuterium distribution at the tip of and in the wake of secondary and tertiary fatigue cracks as well as at MnS inclusions. The use of deuterium eliminates the difficulties of interpreting hydrogen measurements by SIMS relating to the ubiquitous presence of hydrogen in all high vacuum systems and guarantees that deuterium measured by the NanoSIMS must be attributed to the fatigue testing protocol. This methodology has allowed us to directly observe the distribution of hydrogen in dislocation tangles ahead and in the wake of fatigue crack tips and at the interface of MnS inclusions. The protocol provides an avenue by which the path and speed with which hydrogen proceeds along its embrittling course of action may be directly followed through modifications of the fatigue testing parameters and/or alloy type and allows a means to validate at least qualitatively recently published models of enhanced hydrogen transport by dislocations.

Diffusible Hydrogen Facilitated Stress Corrosion Cracking in 316 Stainless Steel Using In-Situ Gaseous Hydrogen Charging in Simulated PWR Environment

Numerical Simulation on Hydrogen Induced Cracking Behavior of 4130X Hydrogen Storage Vessel with Defect

Impact of Diffusible Hydrogen on Corrosion of Alloy 600 at 288°C: an In-Situ Electrochemical Study

Effect of Hydrogen Charging on the Stress Corrosion Cracking Behavior of X70 Steel in Simulated Deep Seawater Environment

Hydrogen effects on passivation and SCC of 2205 DSS in acidified simulated seawater

Effect of hydrogen charging on SCC of 2205 duplex stainless steel with varying microstructures in simulated deep-sea environment

Hydrogen-enhanced oxidation of ferrite phase in stainless steel cladding and the contribution to stress corrosion cracking in deaerated high temperature water

The role of hydrogen in promoting differences in fatigue crack growth rates observed in Type 304/304L stainless steel at elevated temperature

Stress-Corrosion Cracking Sensitization by Hydrogen upon Oxidation of Nickel-base Alloys by Water – an Experiment-Guided First-Principles Study

Analysis of Stress Corrosion Cracking Growth Rate in the Heat-Affected Zone of 316L Based on the Heterogeneity of the Mechanical Properties

Effect of dissolved oxygen and hydrogen on the stress corrosion cracking behavior of alloy 600 in high temperature water

Threshold stress intensity of hydrogen-induced cracking and stress corrosion cracking of high strength steel

Modelling of Hydrogen Distribution at the Fatigue Crack Tip of Austenitic Stainless Steels in Internal and External Hydrogen Tests

The effect of hydrogen on stress corrosion behavior of X65 steel welded joint in simulated deep sea environment

Short communication: "Effect of dissolved hydrogen on the early corrosion behavior of 316 stainless steel in simulated PWR environments"

Effects of hydrogen on the fracture toughness of X80 steel base metal and girth weld under strong cathodic current with in-situ hydrogen charging

Stress corrosion tests for prestressing steels—Part 1: The influence of surface condition and test solution composition on hydrogen charging

High resolution NanoSIMS imaging of deuterium distributions in 316 stainless steel specimens after fatigue testing in high pressure deuterium environment

Study on the roles of bisulfite in the stress corrosion cracking of 7050-T7451 aluminum alloy in the thin electrolyte layer environment

Hydrogen Effect on the Fatigue Crack Growth in Austenitic Stainless Steel Investigated by a New Method Based on Nanohardness Distribution

Strength Effect in Stress Corrosion Cracking of High-Strength Steel in Aqueous Solution