Abstract:<p>In this study, for the first time, the evolution of geometrically necessary dislocation (GND) and statistically stored dislocation (SSD) densities, as well as their roles in strain hardening during mechanical twinning, was experimentally investigated in a tensile-deformed Fe-22Mn-0.6C twinning-induced plasticity (TWIP) steel. GND and SSD densities were estimated via EBSD-acquired orientation data and a modified strain hardening model, respectively. The analysis demonstrates that the GND density increases non-linearly due to mechanical twinning. The SSD density increases much faster than the GND density, which shows that multiplication of the SSDs is heavily dependent on the imposed strain level. It is revealed that the GND density is higher at early strain stages (below 0.14 true strain), dominating dislocation hardening, but thereafter the SSD density contributes more. It is also found that the GND density is several times higher in this TWIP steel than in metals or alloys, which deform through dislocation slip only. We attribute this difference to the planar slip of dislocations and the occurrence of mechanical twinning, which leads to much more pile-ups of the GNDs at/near boundaries. Mechanical twinning directly contributes less than 100 MPa to flow stress increment in the studied true strain range of 0 to 0.34. Consequently, depending on dislocation types, dislocation multiplication governs strain hardening at all deformation ranges. The findings provide insight into the evolution behaviors of GNDs and SSDs in TWIP steels, which are particularly important for further understanding of the dynamic Hall-Petch effect and useful for TWIP alloy design efforts.</p>

Simultaneously Enhancing the Strength and Ductility of Fe–Mn–C Twinning-Induced Plasticity Steel Via Cr/N Alloying

Influence of carbon addition on mechanical properties of Fe–Mn–C twinning-induced plasticity steels

Unusual grain-size effects on tensile deformation behavior of twinning-induced plasticity steel with low Mn content

Strain rate-dependent hardening with dislocation-twin interaction of Fe–Mn–Al–C steel using crystal plasticity

The tensile properties and microstructure evolution of cold-rolled Fe–Mn–C TWIP steels with different carbon contents

The Influence of Cr Addition on the Microstructure and Mechanical Properties of Fe-25Mn-10Al-1.2C Lightweight Steel

Cracking in a Fe–25Mn–3Si–3Al Steel

Synergistic Effect of Al and Ni on Microstructure Evolutions and Mechanical Properties of Fe-Mn-Al-C Low-Density Steels

Enhancement of Yield Strength by Chromium/Nitrogen Alloying in High-Manganese Cryogenic Steel

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength

Twinning Engineering of a CoCrFeMnNi High-Entropy Alloy

Effect of Grain Size on the Plastic Deformation Behaviors of a Fe-18Mn-1.3Al-0.6C Austenitic Steel

Adding N to enhance low-cycle fatigue properties of high-Mn austenitic steel

Achieving excellent strength and ductility synergy by δ phase strengthening in low-density high-manganese steel

Enhancing the strength-ductility trade-off in a NiCoCr-based medium-entropy alloy with the synergetic effect of ultra fine precipitates, stacking faults, dislocation locks and twins

Overcoming high-temperature strength-ductility trade-off by combination deformation twinning of C11b and D022 superlattices in a Ni-Cr-W/Mo-based superalloy

Simultaneous enhancement of strength and ductility via microband formation and nanotwinning in an L12-strengthened alloy

Plastic deformation mechanism of CoCrxNi medium entropy alloys

Multiple deformation mechanisms induced by pre-twinning in CoCrFeNi high entropy alloy

Investigations of dislocation-type evolution and strain hardening during mechanical twinning in Fe-22Mn-0.6C twinning-induced plasticity steel

Twin-induced transformation strengthening of CoCrNi-based medium-entropy alloy with a gradient nanostructure