Abstract:<p>Microstructural and textural characteristics of Zr702 and Zr-2.5Nb alloys before and after rolling (50% reduction in thickness) were characterized and compared by employing electron channel contrast imaging and electron backscatter diffraction techniques, with underlying reasons for the differences between them explored. Results show that the starting microstructure of the Zr702 is mainly comprised of well-equiaxed α-Zr grains while the Zr-2.5Nb presents a typical dual-phase microstructure featured by bulk α grains enclosed by thin β-Zr films. After the 50% rolling, plastic deformation readily occurs through the active operation of prismatic and pyramidal slip in both the Zr alloys. Most grains are found to be elongated along rolling direction with a few less-deformed grains also present (more evident in the rolled Zr702). The β-Zr preexisting in Zr-2.5Nb alloy is softer than α-Zr and could thus be deformed more easily, allowing fewer plastic strains to be accommodated by the α grains. The starting Zr702 has a typical bimodal basal texture that is essentially unchanged after the 50% rolling. The majority of grains in the starting Zr-2.5Nb show scattered orientations with their c-axes away from normal directions (ND). After the same rolling, however, c-axes of most α-grains in the Zr-2.5Nb alloy are aligned to be close to transverse direction or ~30° from the ND (ring-like distribution), different from that of the Zr702. It is demonstrated that the formation of such textural features is related to the preexisting thin β films in the Zr-2.5Nb alloy, in addition to the slip deformation.</p>

Microstructure and Texture Transformation of Wedge-Shaped Rolled 3% Y2O3p/ZGK200 Composites

Microstructure and texture transformation of wedge-shaped rolled 3%Y2O3p/ZGK200 composites

Tailoring the texture and mechanical properties of 3% Y 2 O 3p /ZGK200 composites fabricated by unidirectional and cross rolling followed by annealing

Tailoring the Texture and Mechanical Properties of 3% Y2O3p/ZGK200 Composites Fabricated by Unidirectional and Cross Rolling Followed by Annealing

Microstructure and Texture Transformation of Unidirectional Rolled 3% Y2O3p/ZGK200 Composites During Annealing

Microstructure and texture transformation of unidirectional rolled 3% Y 2 O 3p /ZGK200 composites during annealing

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Effects of Direct Rolling Deformation on the Microstructure and Tensile Properties of the 2.5 Vol% (tibw+ticp)/ti Composites

Evolution of Microstructure, Texture and Mechanical Properties of ZK60 Magnesium Alloy in a Single Rolling Pass

The microstructure and texture evolution of pure molybdenum sheets under various rolling reductions

Microstructure and texture evolution in warm-rolled fine-grained tungsten

Evolution of Microstructure, Texture and Mechanical Properties of SiC/AZ31 Nanocomposite During Hot Rolling Process

Slip Behavior and Its Effect on Rolling Texture Development in a Dual-Phase Mg–Li Alloy

Texture and Twinning Evolution of Cold-Rolled Industrial Pure Zirconium

Non-Basal Slip Induced Rare Earth Texture Evolution in Mg-14Gd-0.5Zr (wt.%) Alloy During the Traditional Hot Rolling

Evolution of texture during hot rolling of aluminum borate whisker-reinforced 6061 aluminum alloy composite

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Effects of rolling deformation on microstructure orientations and tensile properties of TiB/(TA15-Si) composites

Texture Evolution of AZ31 Magnesium Alloy Sheets During Warm Rolling

Microstructural and textural differences between rolled Zr702 and Zr-2.5Nb alloys: The role played by preexisting β phase