Abstract:Pure tungsten (W) is generally believed to be a preferred alternative material for kinetic penetrators once a "self-sharpening" effect can be realized by inducing adiabatic shear failure during high-speed impact. However, it is still a major challenge to trigger adiabatic shear bands (ASBs) in pure W with low ductility. In this work, we reported an improved adiabatic shear susceptibility of pure W by controlling the texture evolution during the pre-rolling process. As the rolling strain increased, the texture components and intensity underwent crucial variations to facilitate the appearance of ASBs. For comparative studies, we investigated the dynamic behavior of three kinds of W samples with different microstructural features at a wide range of temperatures (298K∼1473K) via SHPB system, including coarse-grained W (CGW), as-rolled W samples to the thickness reductions of 75% (75W) and 80% (80W). The experimental results revealed a transition of failure behavior from typical brittle fracture to adiabatic shear instability under uniaxial dynamic compression. Of particular interest was that although 75W and 80W exhibited almost the same mechanical properties after the similar rolling reductions, their dynamic instability behaviors differed remarkably with different spatial distributions of texture components. In the as-rolled 75W, two dominant texture components of {001} and {111} were alternate to form fully spaced layers. Under uniaxial compression, the {111} "hard orientation layers" became the obstacles to the propagation of ASBs. Fortunately, in 80W specimens the different {001} "soft orientation layers" were interconnected by the "soft bricks" of the same orientation, which provided pathways for the expansion of shear localization and ultimately the triggering of ASBs. Through subsequent crystal plasticity finite element (CPFEM) simulations, we further verified the effect of orientation distributions on the shear localization and thoroughly explained the formation mechanism of ASBs in the highly textured refractory metal. This may provide guidance for producing advanced materials for certain practical applications.

Microstructure and texture evolution in warm-rolled fine-grained tungsten

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Evolution of microstructure and texture of moderately warm-rolled pure tungsten during annealing at 1300 °C

Microstructure and Annealing Behavior of Three Rolled Pure Tungsten Plates with Different Thickness Reduction

Evolution of microstructure and texture in a warm-rolled yttria dispersion-strengthened tungsten plate during annealing in the temperature range between 1200 °C and 1350 °C

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Research Progress on Rolling Forming of Tungsten Alloy

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

High-temperature tensile and thermal shock characterization of low-temperature rolled tungsten

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Microstructure evolution and mechanical properties of metastable austenitic medium Mn steel fabricated by warm caliber rolling

Recrystallization behavior of pure tungsten hot-rolled with high accumulated strain during annealing at 1250 C-1350 C

Microstructural Evolution of Ta-4%W During Cold Rolling

Effect of Warm Crossing Rolling on the Microstructure, Texture and Annealing Behavior of High-Purity Tantalum

Effect of Warm Rolling Temperature on the Microstructure and Texture of Microcarbon Dual-Phase (DP) Steel

Effects of Thickness Reduction on Recrystallization Process of Warm-Rolled Pure Tungsten Plates at 1350 °C

Tailoring the adiabatic shear susceptibility of pure tungsten via texture evolution

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Texture and Twinning Evolution of Cold-Rolled Industrial Pure Zirconium

Delving into the intrinsic co-relation between microstructure and mechanical behaviour of fine−/ultrafine-grained TWIP steels via TEM and in-situ EBSD observation

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195