Abstract:The demand for microfluidic pressure sensors is ever-increasing in various industries due to their crucial role in controlling fluid pressure within microchannels. While syringe pump setups have been traditionally used to regulate fluid pressure in microfluidic devices, they often result in larger setups that increase the cost of the device. To address this challenge and miniaturize the syringe pump setup, the researcher introduced integrated T-microcantilever-based microfluidic devices. In these devices, microcantilevers are incorporated, and their deflections correlate with the microchannel's pressure. When the relative pressure of fluid (plasma) changes, the T-microcantilever deflects, and the extent of this deflection provides information on fluid pressure within the microchannel. In this work, finite element method (FEM) based simulation was carried out to investigate the role of material, and geometric parameters of the cantilever, and the fluid viscosity on the pressure sensing capability of the T-microcantilever integrated microfluidic channel. The T-microcantilever achieves a maximum deflection of 127μm at a 5000μm/s velocity for Young's modulus(E) of 360 kPa of PDMS by employing a hinged structure. On the other hand, a minimum deflection of 4.05 × 10-5μm was attained at 5000μm/s for Young's modulus of 1 TPa for silicon. The maximum deflected angle of the T-cantilever is 20.46° for a 360 kPa Young's modulus while the minimum deflection angle of the T-cantilever is measured at 13.77° for 900 KPa at a fluid velocity of 5000μm s-1. The T-cantilever functions as a built-in microchannel that gauges the fluid pressure within the microchannel. The peak pressure, set at 8.86 Pa on the surface of the cantilever leads to a maximum deflection of 0.096μm (approximately 1μm) in the T-cantilever at a 1:1 velocity ratio. An optimized microfluidic device embedded with microchannels can optimize fluid pressure in a microchannel support cell separation.

Application of Embedded Capacitive Pressure Sensors in Pressure Drop Measurement of Microchannels

Microfluidic Channel-Based Soft Electrodes and Their Application in Capacitive Pressure Sensing

Flow Characteristics of Fluids in a Microchannel Driven by Hydrostatic Pressure

A Capacitive Pressure Sensor with Adjustable Working Range for Deep Sea

Measurement System for Characterization of Gas-Liquid Two-Phase Flow in Micro-Channel

PRESSURE FLUCTUATIONS OF LIQUID-LIQUID SLUG FLOW IN CROSS-JUNCTION SQUARE MICROCHANNELS

Measurement of Gas-Liquid Two-Phase Flow in Micro-Pipes by a Capacitance Sensor.

A Device and Method For Flowrate Measurement of Fluid in Small Channel Based on C~4D Technique

On-chip micro pressure sensor for microfluidic pressure monitoring

An Easy Method for Pressure Measurement in Microchannels Using Trapped Air Compression in a One-End-Sealed Capillary

SIMULATION AND MICRO-PIV RESEARCH ON CLASSICAL MICROCHANNEL FLOW

A Facile Pressure Drop Measurement System and Its Applications to Gas–liquid Microflows

Direct Measurement of the Differential Pressure During Drop Formation in a Co-Flow Microfluidic Device

Integrated High-Speed Flow Sensor Based on Pressure Difference Measuring

Optimization of Newtonian fluid pressure in microcantilever integrated flexible microfluidic channel for healthcare application

A Smart Microfluidic System Integrated with Pressure Sensors and Flow Sensor Based on Electrochemical Impedance Methods

Capacitive Micromachined Ultrasonic Transducer for Ultra-Low Pressure Measurement: Theoretical Study

Ultraminiature and Flexible Sensor Based on Interior Corner Flow for Direct Pressure Sensing in Biofluids.

Study of a Novel Capacitive Pressure Sensor Using Spiral Comb Electrodes

Design and Characterization of a Flexible Relative Pressure Sensor With Embedded Micro Pressure Channel Fabricated by Flexible Printed Circuit Board Technology

An Experimental Investigation on Pressure Drop of Steam Condensing in Silicon Microchannels