Abstract:Solid oxide fuel cells (SOFCs) electrochemically convert hydrogen and oxygen into electricity, heat, and water with high efficiency (~55%) [1], while in reverse operation, water and electricity are converted to hydrogen and oxygen in solid oxide electrolysis cells (SOECs). Appropriately designed solid oxide cells (SOCs) can operate in both SOFC and SOEC mode. Conventional SOCs typically demand elevated operating temperatures (800-1000°C), resulting in higher cost and accelerated degradation issues. Lowering operating temperatures below 600°C reduces thermal stresses, shortens start-up times, and broadens applications [2]. Ce 1-x Gd x O 2-δ (GDC), due to its superior oxygen ion conductivity at reduced temperatures, has lower ohmic losses than competing electrolyte materials. Thus, our 1.2 cm diameter circular anode supported GDC cell with 0.31 cm 2 active area exhibits exceptional power densities, reaching approximately 3 watt per square centimeter at 650°C. Through optimal design, these cells exhibit exceptional performances in fuel cell mode, significantly enhancing efficiency and effectiveness when operating as an electrolyzer for fuel generation. This advance in performance is a result of mitigating the leakage current issues typical of ceria-based electrolytes through precise engineering of the cathodic microstructure and surface chemistry modification [3]. The transition from lab-scale to large-scale commercialization (with active areas of 16 cm2 &; 81 cm2) presents significant challenges such as tailoring material properties for large-cell versus button-cell synthesis while maintaining high performance levels. In this work we explore the challenges encountered during the scaling-up process. We report on fabrication strategies employed to achieve cell flatness, maintain high efficiency, ensure cost-effectiveness, and achieve long-term stability. Specifically, we have fabricated graded anode-supported cells [4] by developing an innovative lamination strategy involving tapes oriented perpendicular to each other. This approach notably contributed to achieving superior electrolyte densification and resulted in significantly flatter (low curvature values) with respect to both horizontal and vertical axes in cartesian coordinate space. When compared to the flatness values of 10x10 cm 2 commercially available cells, our cells demonstrated remarkably flatter curvatures as shown in figure 1. This characteristic has proven highly beneficial for stack assembly, minimizing issues such as cell cracking and reducing sealing-related problems. By optimizing the cathode scaffold and infiltration process on larger area cells through a spray-coating machine, scaling up challenges are effectively mitigated compared to the button cell approach, where scaffold preparation and infiltration were performed using blade coating and a hand pipette, respectively. This approach effectively tackles electronic conduction issues in ceria-based electrolytes, leading to higher Open Circuit Voltages (OCVs) in fuel cell mode and increased efficiencies in reversible mode. References: D. Wachsman, and K. T. Lee, Science, 334 , 935 (2011). Q. Minh, Journal of the American Ceramics Society , 76 , 563 (1993). A. Robinson, Y. L. Huang, S. A. Horlick, J. Obenland, N. Robinson, J. E. Gritton, A. M. Hussain, E. D. Wachsman, Advanced Functional Materials , (In press). Ostrovskiy, M. Saqib, J. Hong and E. D. Wachsman, The Electrochemical Society , MA2023-01 , 132 (2023). Figure 1

Construction and Scale-Up of High Performing SOFC with Enhanced GdxCe1−xO2−δ Barrier Layer Self-Crystallization and Defect-Free GDC-YSZ Interface

A high performance intermediate temperature fuel cell based on a thick oxide–carbonate electrolyte

Boosting intermediate temperature performance of solid oxide fuel cells via a tri‐layer ceria–zirconia–ceria electrolyte

In Situ Densification of Gadolinium-Doped Ceria Interlayer by Infiltration Process in SOFC

Conducting Property and Performance Evaluation of LNF As Cathode Current Contact Layer in Solid Oxide Fuel Cell

Enhancement of the Cathode/electrolyte Interface by a Sintering-Active Barrier Layer for Solid Oxide Fuel Cells

Enhanced Cathode/Electrolyte Interface by a Nano-Modified Barrier Layer for Solid Oxide Fuel Cells

Low Temperature Deposited (ce,gd)o2−x Interlayer for La0.6Sr0.4Co0.2Fe0.8O3 Cathode Based Solid Oxide Fuel Cell

Scalable and facile fabrication of tri-layer electrolytes by reactive sputtering for efficient and durable solid oxide fuel cells

One-step preparation of large-size 1.5-μm-thick robust YSZ electrolyte for high CH 4 conversion SOFCs at 600 °C

Preparation, Evaluation, and Application of SUS430/441 Interconnect with Mn-Co Coating in Solid Oxide Fuel Cells

Highly dense and ultrathin gadolinia-doped ceria interlayer for enhanced performance of large-area anode-supported solid oxide fuel cell

Performance and Stability Analysis of SOFC Containing Thin and Dense Gadolinium-Doped Ceria Interlayer Sintered at Low Temperature

Transitioning Low-Temperature GDC Socs: Lab to Commercialization Scale

Hierarchically oriented macroporous anode-supported solid oxide fuel cell with thin ceria electrolyte film.

Boosting Electrochemical Performance via Extra‐Role of La‐Doped CeO2‐δ Interlayer for "Oxygen Provider" at High‐Current SOFC Operation

Controlling Yttria-stabilized zirconia/gadolinia-doped ceria interdiffusion layer in the solid oxide fuel cell electrolyte via flash sintering method

In situ self-assembled NdBa0.5Sr0.5Co2O5+δ/Gd0.1Ce0.9O2-δ hetero-interfaces enable enhanced electrochemical activity and CO2 durability for solid oxide fuel cells

Preparation of Doped Ceria Anode/Electrolyte Double-Layer Structure by Tape Casting and Co-Sintering

Durability Study of Anode-Supported SOFC with Large-Area Fabricated By 4-Layer Sequential Co-Lamination and GDC Co-Firing Process

Lower Down Both Ohmic and Cathode Polarization Resistances of Solid Oxide Fuel Cell Via Hydrothermal Modified Gadolinia Doped Ceria Barrier Layer