Abstract:A new technology to the pharmaceutical field is presented: surface decontamination by plasmas The technology is comparable to established barrier systems like e-beam, volatile hydrogen peroxide, or radiation inactivation of microbiological contaminations. This plasma technology is part of a fully automated and validated syringe filling line at a major pharmaceutical company and is in production operation. Incoming pre-sterilized syringe containers ("tubs") are processed by plasma, solely on the outside, and passed into the aseptic filling isolator upon successful decontamination. The objective of this article is to present the operating principles and develop and establish a validation routine on the basis of standard commercial biological indicators. Their decontamination efficacies are determined and correlated to the actual inactivation efficacy on the pharmaceutical packaging material.The reference setup is explained in detail and a short presentation of the cycle development and the relevant plasma control parameters is given, with a special focus on the in-process monitor determining the cycle validity. Different microbial inactivation mechanisms are also discussed and evaluated for their contribution and interaction to enhance plasma decontamination. A material-dependent inactivation behavior was observed. In order to be able to correlate the tub surface inactivation of Geobacillus stearothermophilus endospores to metallic biological indicators, a comparative study was performed. Through consistently demonstrating the linear inactivation behavior between the different materials, it becomes possible to develop an effective and time-saving validation scheme. Lay abstract: The challenge in new decontamination systems lies in a thorough validation of the inactivation efficacy under different operating regimes. With plasma, as an ionized gas, a new barrier concept is introduced into pharmaceutical aseptic processing of syringes. The presented system operates in vacuum and only decontaminates the outer surface of pre-sterilized syringe containers ("tubs"), before they are transferred into the aseptic area. The plasma does not penetrate into the tub. This article discusses the phase from development and test germ selection, across the identified sporicidal mechanisms, to a proposal for a validation scheme on the basis of commercially available biological indicators. A special focus is placed on an extensive investigation to establish a link between the tub surface microbial kill (polystyrene and Tyvek(and (2)) ) and biological indicator inactivation (stainless steel). Additionally, a rationale is developed on how an optical in-process monitor can be applied to establish a validatable limit on the base of the predetermined inactivation data of Geobacillus stearothermophilus endospores.

Flexible Thin-Layer Plasma Sterilizer Based on Polyimide and Efficacy Evaluation under Bending Deformation

State-of-the-art non-thermal plasma disinfection and medicine

Rapid Disinfection Performance of a Touchable Pulsed SDBD Nonthermal Plasma

The effect of bending angle on a flexible electrode DBD plasma under sinusoidal excitation

A novel flexible plasma array for large-area uniform treatment of an irregular surface

Low-Pressure Microwave Plasma Sterilization of Slender Tube Inner Surfaces

Plasma Decontamination: A Case Study on Kill Efficacy of Geobacillus stearothermophilus Spores on Different Carrier Materials

Surface Sterilization By Atmospheric Pressure Non-Thermal Plasma

Proposing an Affordable Plasma Device for Polymer Surface Modification and Microbial Inactivation

A low power flexible dielectric barrier discharge disinfects surfaces and improves the action of hydrogen peroxide

The Cold and Atmospheric-Pressure Air Surface Barrier Discharge Plasma for Large-Area Sterilization Applications

Experimental Investigation of Low-Pressure Microwave Plasma with Oxygen and Argon for Internal Sterilization of Medical Devices with Slender Catheters

Development of a New Atmospheric Pressure Cold Plasma Jet Generator and Application in Sterilization

Characterization of Sputter-coated Polyethylene Naphthalate-Foil as Novel Flexible Surface DBD Plasma Source

The Application of a Non-Thermal Plasma Generated by Gas–liquid Gliding Arc Discharge in Sterilization

Polyimide‐Based Flexible Plasma Sheet and Surface Ionization Waves Propagation (adv. Electron. Mater. 11/2021)

Study on Flexible Surface Dielectric Barrier Discharge Plasma Film for in Situ Inactivation of Bacteria and Viruses

Realizing high efficiency and large-area sterilization by a rotating plasma jet device

A Novel Approach on Dielectric Barrier Discharge Using Printed Circuit Boards

Sterilization of Bacteria with Low-Pressure Low-Temperature Plasma Discharge

Modelling of Nonthermal Dielectric Barrier Discharge Plasma at Atmospheric Pressure and Role of Produced Reactive Species in Surface Polymer Microbial Purification