Abstract:Lead zirconate titanate and polydimethylsiloxane (PZT–PDMS) thin films are an attractive choice for a flexible piezoelectric substrate. In this work, the surface modification of the PZT–PDMS composite with plasma treatment is developed to fabricate flexible conductor patterns or devices directly on the composite surface. Optimized plasma treatment conditions are achieved by varying plasma parameters such as the pressure of treatment, type of gas, gas flow, and time of treatment. Plasma polymerization is carried out using C2H4–CO2, and argon (Ar) is used for the surface ablation effect in low-pressure conditions. Atmospheric pressure plasma (APP) is performed in a N2 atmosphere which has a surface etching effect. All the treatments create a hydrophilic layer, which is confirmed with water contact angle measurements, X-ray photoelectron spectroscopy, and Fourier transform infrared analysis. Silver conductive ink was printed on the plasma-treated films to fabricate flexible conductive patterns, and the bonding strength was tested by performing adhesive tests such as tape, ultrasonic, and soak tests. APP treatment under a N2 environment with a 300 V input voltage, 21.5 kHz frequency, and 2 min deposition time proves to be the most efficient surface modification technique. This treatment produces a silica-like layer on the composite surface and results in better wettability. It reduces the contact angle from 108 to 20° immediately after the treatment and shows strong adhesion during several rigorous adhesion tests. The printed conductive patterns on the N2-treated film show strong mechanical stability and exhibit great electric conductivity under bending and releasing. The APP treatment under N2 environment can overcome the adhesion issue of the printed conductive layer on the hydrophobic composite surfaces. Moreover, all the above plasma treatments have a negligible effect on the piezoelectric properties of PZT–PDMS films.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsapm.0c01117.Low-pressure, capacitively coupled RF plasma reactor used for surface treatment of PZT–PDMS films, schematic drawing of the atmospheric pressure DBD plasma reactor used for surface treatment of the PZT–PDMS films, original images of XPS analysis and elemental quantification of untreated and treated films, and contact angles measured after 48 h of treatment (PDF)Measurement of the charge response of piezoelectric PZT–PDMS films (MP4)This article has not yet been cited by other publications.

Polyimide‐Based Flexible Plasma Sheet and Surface Ionization Waves Propagation (adv. Electron. Mater. 11/2021)

Ionization Wave Propagation of a Surface Dielectric Barrier Discharge with a Flexible-Structure Plasma Sheet

In Situ Measurement of Dynamic Surface Charge on Dielectrics Interacted with Plasma Jet Arrays

Flexible Thin-Layer Plasma Sterilizer Based on Polyimide and Efficacy Evaluation under Bending Deformation

Localized Surface Hydrophilicity Tailoring of Polyimide Film for Flexible Electronics Manufacturing Using an Atmospheric Pressure Ar/H2O Microplasma Jet

Microwave atmospheric pressure plasma jet generated from substrate integrated waveguide resonator

Enduring And Stable Surface Dielectric Barrier Discharge (Sdbd) Plasma Using Fluorinated Multi-Layered Polyimide

Flexible System for Multiple Plasma Immersion Ion Implantation-Deposition Processes

Controlling the triboelectric properties and tribological behavior of polyimide materials via plasma treatment

Visual Phenomena of Surface Plasmon Polaritons at the Dielectric-Plasma Interface

Visualization of Electrical Interaction among Close-Packed Atmospheric Pressure Plasma Jets

Plasma Ion Implantation to Thin Polymer Foils

Plasma Treatment of Composite Piezoelectric Thin Films for Good Adhesion of Printed Conductive Ink

Inside Front Cover: Plasma Process. Polym. 4/2021

Influence of Low Temperature Plasma Treatment on Surface Insulation Performance of Polyimide Film

Charging and Discharging Mechanism of Polyimide under Electron Irradiation and High Voltage

Plasma-surface Interaction: Dynamic Evolution of Interfacial Pattern Modes During Transformation Process from Dielectric to Metallic Substrate

Plasma–Liquid Interface Manipulated by Chamber Structure: An Experimental and Theoretical Approach

A Planar-Type Surface-Wave Plasma Source with A Subwavelength Diffraction Grating Inclusion for Large-Area Plasma Applications

Polyimide as a versatile enabling material for microsystems fabrication: surface micromachining and electrodeposited nanowires integration

Fabrication and Performance of Insulating Polyimide Layers of Micro-Plasma Reactors