Abstract:For further knowledge about the refining performance of AlTiC master alloys, A15.5Ti0.25C and A16.5Ti0.5C master alloys containing high Ti and C content were prepared and used in grain refining experiments of 99.8% commercial pure aluminum(CPAl). Their performance was compared with two types of Al5Ti1B refiners whose performance was nowadays considered to be the best. These two types of master alloys show similar refining efficiency at the addition level of 0.2%. However, at the addition level of 0.5%, there still exists great performance difference between AlTiC and Al5TiB alloys in grain refinement of 99.98% and 99.995% high purity aluminum(HPAl). The growth of columnar grains is fully suppressed due to the refinement of AlTiC at the addition level of 0.5%. Also, at the same addition level, the grain refining experiments of A13Ti0.15C and A15Ti0.2C master alloys which have found initial commercial applications are conducted in the above-mentioned three types of pure aluminum. According to the experimental results, these two refiners of different compositions are both nonideal. The second phase particles extracted from each refiner were observed through TEM, while the nuclei of grains after grain refinement were observed through SEM. The results were analyzed through computation and comparison of the constitutional-supercooling parameter and the growth-restriction parameter whose values were determined by solute element in aluminum melt with different purity. Apparently, AlTiC master alloys with high content of Ti and C element have great refining potential.

Grain Refining Efficiency of Al-V-B Master Alloy in A356.2 Alloy under Different Inoculated Temperatures and Holding Times

Effect of Vanadium/Boron Ratio on the Microstructure of Al-V-B Master Alloy and Their Grain Refining of Alloy A356.2

Study on the Grain Refinement of A356 Alloy by Al–3 Wt-% VN Master Alloy

Grain refining performance of Al–Ti master alloys with different microstructures

Grain refinement of A356 alloy by Al–Ti–B–C master alloy and its effect on mechanical properties

Study on Grain Refinement of A357 Alloy Using Al-5Ti-1B

Grain refinement and eutectic modification of A356 casting alloy by adding Al-B-Sr master alloys and its effect on tensile properties

Grain refinement and mechanical properties of Mg–5Li–3Al alloy inoculated by Al–5Ti–1B master alloy

Influences of Preparation Conditions and Melt Treatment Procedures on Melt Treatment Performance of Al-5Ti-B and Al-10Sr Master Alloys

High-Temperature In-Situ Synthesis and Formation Mechanism of Vb2 Substrates in Al-V-B Grain Refiner

Research of Grain Refining on Pure Al by Three Different Master Alloys

Effect of Al-3 wt% Al2O3 master alloy fabricated by calcined kaolin on grain refinement and mechanical properties of A356 alloy

Hereditary Effect of Al-based Modifiers and Grain Refiners on Structure and Properties of A356.2 Alloys

Optimization of Processing Parameters for Preparation of Al-3Ti-1B Grain Refiner

Study on Grain Refinement and Refining Mechanism of Al-Si-Mg Alloy

Nucleation mechanism for grain refinement in A357 alloy by Al-Ti-B master alloys

On the Understanding of Aluminum Grain Refinement by Al-Ti-B Type Master Alloys

The Behavior of AlTiC Master Alloys in Grain Refining of Commercial and High Pure Aluminum

Performance Comparison of AlTiC and AlTiB Master Alloys in Grain Refinement of Commercial and High Purity Aluminum

Concurrent effects of various B additions on grain refinement, Fe intermetallics morphologies, and ductility evolution of Al-7.5Si-0.55 Mg (A357) cast alloy

High-temperature in-situ synthesis and formation mechanism of VB 2 substrates in Al-V-B grain refiner