Abstract:Given the accelerating depletion of iron ore resources, there is growing concern within the steel industry regarding the availability of high-phosphorus iron ore. However, it is important to note that the utilization of high-phosphorus iron ore may result in elevated phosphorus content and notable fluctuations in molten iron, thereby imposing additional challenges on the dephosphorization process in steelmaking. The most urgent issue in the process of converter steelmaking is how to achieve efficient dephosphorization. In this study, the influence of various factors on the logarithm of the phosphorus balance distribution ratio (lgLp), the logarithm of the P2O5 activity coefficient (lgγP2O5), and the logarithm of the phosphorus capacity (lgCp) were examined through thermodynamic calculations. The impact of each factor on dephosphorization was analyzed, and the optimal conditions for the dephosphorization stage of the converter were determined. Furthermore, the influence of basicity and FetO content on the form of phosphorus in the slag was analyzed using FactSage 7.2 software, and the precipitation rules of the slag phases were explored. The thermodynamic calculation results indicated that increasing the basicity of the dephosphorization slag was beneficial for dephosphorization, but it should be maintained below 3. The best dephosphorization effect was achieved when the FetO content was around 20%. The reaction temperature during the dephosphorization stage should be kept low, as the dephosphorization efficiency decreased sharply with the increasing temperature. In dephosphorization slag, Ca3(PO4)2 usually formed a solid solution with Ca2SiO4, so the form of phosphorus in the slag was mainly determined by the precipitation form and content of Ca2SiO4. The phases in the dephosphorization slag mainly consisted of a phosphorus-rich phase, an iron-rich phase, and a matrix phase. The results of scanning electron microscopy and X-ray diffraction analyses were consistent with the thermodynamic calculation results.

Effect of Phosphorus Content on Interfacial Heat Transfer and Film Deposition Behavior During the High-Temperature Simulation of Strip Casting

Solidification Structure of Low Carbon Steel Strips with Different Phosphorus Contents Produced by Strip Casting

Effect of Phosphorus on the Microstructure and Mechanical Properties of Strip Cast Carbon Steel

Effect of Boron on the Formation of the Naturally Deposited Film and Its Corresponding Interfacial Heat Transfer Behavior in Strip Casting of Boron-Containing Steel

Inversed Phosphorus Segregation in Twin Roll Cast Strips for Improvement of Mechanical Properties and Weathering Resistance

Study on the Effect of Different Factors on the Change of the Phosphorus-Rich Phase in High Phosphorus Steel Slag

Experimental Study of High Temperature Phase Equilibria in the Iron-Rich Part of the Fe-P and Fe-C-P Systems

Research methods and influencing factors of interfacial heat transfer during sub-rapid solidification process of strip casting

Effect of highly oxidizing converter dephosphorization slag on dephosphorization behaviour of molten steel

Heat transfer behavior in ultrahigh-speed continuous casting mold

Effect of Temperature on Dephosphorization of Hot Metal in Double‐Slag Converter Steelmaking Process by High‐Temperature Laboratorial Experiments

Precipitation behaviour of phosphorus in high strength IF steel during laminar cooling

Interfacial Heat Transfer Behavior at Metal/die in Finger-Plated Casting During High Pressure Die Casting Process

Effect Mechanism of α-Ferrite Sustained Precipitation on High-Temperature Properties in Continuous Casting for Peritectic Steel

Effect of Strip Entry Temperature on the Formation of Interfacial Layer During Hot-Dip Galvanizing of Press-Hardened Steel

Effect of Cr Content on the Microstructure of Casting Infiltration Layers: Simulations and Experiments

Effect of Phosphorus on Hot Ductility of High Manganese Austenitic Steel

Study on Efficient Dephosphorization in Converter Based on Thermodynamic Calculation

Effect of Coating on Instantaneous Interfacial Heat Transfer During Near-Rapid Solidification

The improvement of weathering resistance by increasing P contents in cast strips of low carbon steels

On the Formation of P-Rich Surface Layer of Twin-Roll Cast High-P Strip