Abstract:Publication date: 10 January 2022 Source: Solid State Phenomena Vol. 327 Author(s): Jiehua Li, Maria Pammer, Ernst Neunteufl, Peter Schumacher AZ80 alloy has been widely used to produce high performance Mg casting and wrought parts for high-end applications due to its high mechanical properties and deformation ability. However, at least two important issues still need to be solved in order to further improve its mechanical properties and deformation ability. Firstly, the grain size of α-Mg in AZ80 alloy is relatively large (more than 1000 μm) due to a lack of efficient grain refinement methodologies. Secondly, the size of the eutectic Mg17Al12 phase is also large and the distribution of the eutectic Mg17Al12 phase is continuous, which is very harmful for the mechanical properties, in particular to elongation. In this paper, these two important issues are investigated by adding Mg3N2 sub-micron particle into AZ80 alloy and thereby refining the α-Mg and the eutectic Mg17Al12 phase. Firstly, the Mg3N2 sub-micron particle was directly added into AZ80 alloy by using mechanically stirring in the semi-solid state, subsequently the melting temperature was increased above the liquidous temperature, and finally the melting was casted in the liquid state. It was found that the grain size of α-Mg can be refined from 883.8 μm to 169.9 μm. More importantly, the eutectic Mg17Al12 phase was also refined and the distribution became discontinuous. It should be noted that directly adding the Mg3N2 sub-micron particle into AZ80 alloy leads to a great loss of the Mg3N2 sub-micron particle due to the weak wetting behavior between the Mg3N2 sub-micron particle and Mg melt. The second methodology through mixing Mg3N2 sub-micron particles with AZ91 chips using a twin extruder was also used to prepare AZ91 master alloy with 3wt.% Mg3N2 sub-micron particle, which was subsequently added into AZ80 alloy in the liquid state. In this way, a significant grain refinement of α-Mg and a simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy was also achieved. The grain size of α-Mg can be refined from 883.8 μm to 325.9 μm. However, no significant grain refinement by using UST was observed. Instead, the grain size increases from 325.9 μm to 448.6 μm, indicating that the Mg3N2 sub-micron particle may lose its grain refinement potency due to possible aggregation and clustering. This paper provides an efficient and simple methodology for the grain refinement of α-Mg and the simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy.

Exceptional Grain Refinement Induced by Dispersed MgO Particles in TIG-welded AZ31 Alloy

Achieving columnar-to-equiaxed transition to reduce hot cracking susceptibility in TIG-welded AZ31 alloy through MgO modification

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Exceptional grain refinement of Mg-Zr master alloy treated by tungsten inert gas arc re-melting with ultra-high frequency pulses

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Microstructure and Strengthening Mechanism of TIG Welded Joints of a Mg-Nd-Gd Alloy: Effects of Heat Input and Pulse Current

A New Method for Refinement of Ti-6Al-4 V Prior-Β Grain Structure in the Alternating Magnetic Field Assisted Narrow Gap Gas Tungsten Arc Welding (AMF-GTAW) Via Filler Wire Oscillation

Influence of AZ61 Filler Composition on Grain Refinement of Mg-Al-Zn Alloy GTA Welds

Achieving fully equiaxed grain microstructure and isotropic mechanical properties in wire arc additive-manufactured Mg-Y-Nd-Zr alloys

Microstructure Refinement After the Addition of Titanium Particles in AZ31 Magnesium Alloy Resistance Spot Welds

Development of novel lightweight and cost-effective Mg–Ce–Al wrought alloy with high strength

Study of Microstructure and Properties of AZ91 Magnesium Alloy Welded Joint with Magnetic Field and TiO2 Activated Flux

Achieving excellent strength-ductility combination of Al-aided Mg-Gd-Al-Zr-Zn alloys fabricated by cold metal transfer-based wire-arc directed energy deposition via uniform equiaxed grains and multiple precipitates

Realization of structural evolution in grain boundary, solute redistribution and improved mechanical properties by adding TiC<sub>nps</sub> in wire and arc additive manufacturing 2219 aluminium alloy

Formation and Strengthening Mechanism of Equiaxial Cellular Grain Zone in AA2195-T8 Al–Cu–Li Alloy Twin-Wire P-VPPA Welded Joint with Ti–Zr Microalloying

Enhanced Strength‐Ductility Synergy of Mg‐6Zn Alloy Wire by Inducing GP Zone Precipitation

Improvement of the Microstructure and Mechanical Properties of Welded Joint of Wire Arc Additive Manufacturing-AZ31B Magnesium Alloy by Using AC/DC Mixed Current Waveform in Tungsten Inert Gas Welding

Evolution of grain structure, texture and mechanical properties of a Mg–Zn–Zr alloy in bobbin friction stir welding

Addressing the Abnormal Grain Coarsening During Post-Weld Heat Treatment of TIG Repair Welded Joint of Sand-Cast Mg-Y-RE-Zr Alloy

Effect of the Mg3N2 Sub-Micron Particle on the Grain Refinement of AZ80 Alloy

Microstructure refinement and mechanical properties enhancement of Mg Al alloys via a novel of MgO nanoparticles modified graphene nanoplates refiner by in-situ synthesis