Abstract:High molecular weight polyether polyols are widely used. However, there is not only a large risk of reaction heat, but also a long reaction time in its traditional production process by using the semi-continuous reactor. The microchannel reactor（MCR） has the characteristics of high heat transfer efficiency and process safety,but the viscous material and high reaction heat release make it difficult to produce the high molecular weight polyether polyols. In this work, using double metal complex（DMC） as catalyst and n-hexane as solvent, the ringopening polymerization of propylene oxide（PO） was carried out in MCR. Polypropylene glycol（PPG） with molecular weight ranging from 2000 to 8000 was prepared. Effects of reaction conditions, such as flow rate, channel length,reaction temperature and feed policy, were investigated. It has been found that when the residence time is long enough, the molecular weight of the produced PPG is basically equal to the theoretical molecular weight. When the flow rate of initiator is fixed, an increase in flow rate of monomer will result in the molecular weight distribution（MWD） first widened and then narrowed. If the tube length is longer, the molecular weight is larger and the MWD is wider. If the temperature increases, the induction period of the polymerization can be shortened. Using the segmented feed, it is easier to prepare high molecular weight PPG with higher conversion than using the single feed, but the MWD is wider. These rules can be explained from the mechanism of PO ring-opening polymerization catalyzed by DMC and micro-mixing strength of materials in MCR. The lower the micro-mixing strength, and the smaller the rate ratio of chain transfer to chain propagation in polymerization, the wider the molecular weight distribution is.

PREPARATION OF POLYTETRAMETHYLENE GLYCOL BY BF3 SYSTEM

Preparation of high molecular weight polypropylene glycol in microchannel reactor

SYNTHESIS OF AROMATIC POLYESTERS FROM ESTERS OF DIPHENOLIC ACID AND ISOPHTHALOYL CHLORIDE BY INTERFACIAL POLYCONDENSATION

Preparation and Characterization of Poly(vinylidene Fluoride) Flat Sheet Membrane with Tg Tunable Amphiphilic Terpolymer As Membrane Additive

EFFECT OF ETHYLENE GLYCOL ON POLYMERIZATION OF TETRAHYDROFURAN AND MOLECULAR WEIGHT OF PRODUCT

PREPARATION OF ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE USING STRUCTURED NANOPARTICAL ZIEGLER-NATTA CATALYSTS

Preparation of Porous PVDF Membrane Via Thermally Induced Phase Separation with Diluent Mixture of DBP and DEHP

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Synthesis of Ultrahigh-Molecular-weight Ethylene-1-hexene Copolymers with High Hexene Content Via Living Polymerization with Fluorinated Bis(phenoxy-Imine) Titanium(iv).

Preparation and Characterization of Mono‐ and Di‐d‐α‐tocopheryl Polyethylene Glycol 1000 Succinate

Tetrahydrofuran polymerization initiated by heteropolyacid in the presence of ethylene oxide: Reaction behavior of water and glycol

TETRAHYDROFURAN POLYMERIZATION INITIATED\=WITH HETEROPOLYACID . REACTION BEHAVIOR OF ETHYLENE OXIDE

Effective promotion of tetrahydrofuran polymerization initiated with heteropolyacid

Synthesis and characterization of new type polytetrahydrofuran polyol

Preparation and fluorine enrichment behavior of fluorinated polyester

Ethylene Glycol Purification by Melt Crystallization: Removal of Short-Chain Glycol Impurities

Studies on Mechanism of Tetrahydrofuran Polymerization Initiated by a Heteropolyacid

Ethylene Oxide Promoted Polymerization of Tetrahydrofuran Initiated with Low Concentration of Heteropolyacid

High Molecular Weight Biodegradable Poly(Ethylene Glycol) Via Carboxyl-Ester Transesterification

Preparation and characterization of polyethylene glycol/poly(L-lactic acid) blends

Control of Molecular Weight in Tetrahydrofuran Polymerization Initiated by Heteropolyacid