Abstract:In this study, integrated experimental tests and computational modeling are proposed to investigate the failure mechanisms of open-hole cross-ply carbon fiber reinforced polymer (CFRP) laminated composites. In particular, we propose two effective methods, which include width-tapered double cantilever beam (WTDCB) and fixed-ratio mixed-mode end load split (FRMMELS) tests, to obtain the experimental data more reliably. We then calibrate the traction-separation laws of cohesive zone model (CZM) used among laminas of the composites by leveraging these two methods. The experimental results of fracture energy, i.e. G Ic and G Tc , obtained from WTDCB and FRMMELS tests are generally insensitive to the crack length thus requiring no effort to accurately measure the crack tip. Moreover, FRMMELS sample contains a fixed mixed-mode ratio of G IIc /G Tc depending on the width taper ratio. Examining comparisons between experimental results of FRMMELS tests and failure surface of B-K failure criterion predicted from a curve fitting, good agreement between the predictions and experimental data has been found, indicating that FRMMELS tests are an effective method to determine mixed-mode fracture criterion. In addition, a coupled experimental-computational modeling of WTDCB, edge notched flexure, and FRMMELS tests are adopted to calibrate and validate the interfacial strengths. Finally, failure mechanisms of open-hole cross-ply CFRP laminates under flexural loading have been studied systematically using experimental and multi-scale computational analyses based on the developed CZM model. The initiation and propagation of delamination, the failure of laminated layers as well as load-displacement curves predicted from computational analyses are in good agreement with what we have observed experimentally.

Validating the Efficacy of Deformation Distribution Measurement in CFRP Laminates During Three-Point Bending Using the Sampling Moire Method

Microscale Strain Distribution Measurement Before and after Crack and Delamination Occurrence in CFRP Laminates by Multiplication Sampling Moiré Method

Nonlinear Fracture Analysis of Delamination Crack Jumps in Laminated Composites

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

Numerical Simulation on Mechanical Properties and Damage Behavior of CFRP with Self-Healing Microvascular Channels

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

CFRP Strengthened RC Beams with Pre-Strengthening Non-Uniform Reinforcement Corrosion Subjected to Post-Strengthening Wetting/drying Cycles

Low-velocity impact behavior and residual tensile strength of CFRP laminates

A Coupled FEM-FFT Concurrent Multiscale Method for the Deformation Simulation of CFRPs Laminate

Progressive failure analysis of CFRP composite laminates under uniaxial tension using a discrete element method

Progressive Failure Analysis of Laminated CFRP Composites under Three-Point Bending Load

In-situ Damage Monitoring and Numerical Characterization of Three-Point Bending and Incremental Cycle Flexural Behavior of FMLs

A Combined Experimental and Computational Analysis of Failure Mechanisms in Open-Hole Cross-ply Laminates under Flexural Loading

Numerical Analysis for Damage Detection in CFRP Bolted Joints Using Strain Measurement

An Interface-Dependent Model of Plateau Fracture Toughness in Multidirectional CFRP Laminates under Mode I Loading

Angle-ply orientation-dependent failure behaviors of carbon fiber reinforced polymer laminates

Numerical modelling of the mode I fracture behavior in composite laminates with significant R-curve effect

Experimental Investigation on Deformation and Strength of Carbon/epoxy Laminated Curved Beams

The Compressive Behavior of CFRP Laminates with Delamination of Different Shapes Using Numerical and Experimental Approaches

Study on Delamination Damage of CFRP Laminates Based on Acoustic Emission and Micro Visualization

Strain Rate‐dependent Deformation Behaviors of Multi‐layer Carbon Fiber Reinforced Polymer Laminates