Abstract:Zirconia toughened alumina (ZTA) ceramics are widely used in civilian and defense sectors. Particularly, the introduction of structural gradients has demonstrated the effectiveness of ZTA under complex working conditions and lightweight applications. Present attempts at using additive manufacturing on composition-graded ZTA shaping are still challenging, while few studies have explored its toughening behavior and mechanical properties in practice. This study introduces a novel 3D printing process, the Selective Paste Extrusion Process (SPEP), to effectively fabricate ZTA structures with composition gradients at room temperature. A class of ZTA feedstocks, characterized by a high solid loading of approximately 84 wt% and composed of nano-zirconia and alumina powders, has been developed to enable printing. The printing process of ZTA feedstocks with varied zirconia contents and the microstructure and mechanical properties of both printed non-graded and graded ZTA samples at different sintering temperatures are investigated. Further, a forecast mathematic model is developed for composition-graded ZTA structures, validated by three-point bending experiments. The experimental results show that the graded ZTA sample, with a zirconia composition ratio ranging from 10 to 20 mol%, achieves a hardness of 9.33 GPa and a 7.96 % increase in the maximum bending limit load compared to the non-graded rod. These samples also exhibit a uniform transition along the composition gradient at the interfaces, with corresponding uniform variations in hardness. This study provides a comprehensive and reliable approach for the rapid fabrication of gradient material components in ZTA, offering valuable insights and guidelines for designing gradient components.

Grain Size Refinement of Additive Manufactured Ce-TZP Ceramics by Coupled Two-Step Pre-Sintering and HIP

Stronger and Tougher Nanosized Dense Ceria-Doped Tetragonal Zirconia Polycrystals by Sinter-Hip

Activating Continuous Dislocation Pinning Enhanced Toughness of Nanocomposite Coating Through Specially Oriented Semicoherent Heterointerface Lattice Distortion

Second Phase Strengthening and Grain Boundary Segregation Effects on the Microstructure and Properties of (Ce, Y)-TZP-Based Ceramics Prepared by Vat Photopolymerization

Mechanical properties and low temperature degradation (LTD) of cation-stabilized zirconia

Sintering kinetics of cerium-stabilised tetragonal zirconia

Ultrastrong Tough Zirconia Ceramics by Defects‐engineering

Comparison of sintering behavior and reinforcing mechanisms between 3Y-TZP/Al2O3(w) and 12Ce-TZP/Al2O3(w) composites: Combined effects of lanthanide stabilizer and Al2O3 whisker length

Fabrication, microstructure and mechanical properties of in situ Al2O3 platelets reinforced Ce-TZP composites

A Novel Approach to Improving the Electromechanical Properties of PZT-based Piezoelectric Ceramics Via a Grain Coating Modification Strategy

Compositionally Graded Structures of Zirconia Toughened Alumina Using Extrusion-Based 3D Printing

Preparation of Cepo4 Modified Zro2 Ceramics with Different Particle Sizes and Their Mechanical Behaviors

Stabilization of phase‐pure tetragonal zirconia ceramics with minimum CeO2 doping and associated benefits

Evaluation of Fracture Toughness of Zirconia Ceramics with Heterogeneous Yttrium Distribution Microstructures

PREPARATlON AND SINTERING BEHAVIOR OF Al2O3/10Ce-TZP COMPOSITES FOR ARTIFICIAL JOINT

Enhanced Densification of Ultrafine Ti(C, N)-based Cermets Based on Grain-Growth Induced Liquid-Phase Pore Filling Mechanism

Towards high strengthening efficiency of equiaxed and platelet-shaped alumina reinforced zirconia ceramics with textured microstructure using DLP-based stereolithography

Microwave sintering of Ce-Y-ZTA composite

Preparation of CePO4-coated Zirconia Ceramics and Their Mechanical Behavior

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Microstructure and mechanical properties of dense ZTA ceramics with high Cr2O3 solution