Abstract:Ti6Al4V (TC4) alloy has been widely applied in the military, industrial, chemical, and medical fields due to their excellent thermal stability, corrosion resistance , and biocompatibility. However, titanium alloys are notorious for their poor tribological properties, such as their high friction coefficients and low surface bearing capacities. To tackle this problem, combination of laser surface texturing (LST) and double glow plasma chromizing was conducted to improve the wear resistance of TC4. LST was first conducted to produce uniform dimples with a diameter of 300 μm and gradient density of 11 % on the Ti6Al4V substrate. A chromizing coating (Cr-coating) was subsequently deposited on the surfaces of the textured and raw Ti6Al4V alloy by double glow plasma surface alloying (DGPSA). A continuous and compact Cr-coating with a thickness of about 55 μm was formed on TC4 after being maintained at a temperature of 850 °C, and the coating was mainly composed of a solid solution and intermetallic compounds of Cr 2 Ti phases. The surface hardness after alloying was two times higher than that of the TC4 substrate. Comparative assessments on the wear resistance of the Cr-coatings with and without LST treatment and the TC4 alloy were carried out using a ball-on-disk wear tester. The results showed that the mass loss and specific wear rate of the duplex-treated sample were 1.54 mg and 7.14 × 10 −4 mm 3 ·N −1 ·m −1 . The mass loss and specific wear rate of the TC4 were 4.32 mg and 1.62 × 10 −3 mm 3 ·N −1 ·m −1 . The specific wear rates of the four tested samples were in the following order: the duplex-treated TC4 < textured TC4 < chromized TC4 < polished TC4. The coating obtained by LST-double glow plasma chromizing duplex treatment exhibited an outstanding durability and the best mechanical performance. Thus, this approach be used for the protection of Ti6Al4V surface in engineering components and medical instruments.

Enhancing Wear Resistance of Aluminum Alloy by Fabricating a Ti-Al Modified Layer Via Surface Mechanical Attrition Treatment

Facile fabrication of aluminium alloys with gradient nanostructures incorporating α-Al 2 O 3 particles for enhanced tribological properties

Improvement of tribological performance by micro-arc oxidation treatment on selective laser melting Ti6Al4V alloy

Manipulation Tribological Behavior of Ti6Al4V Alloy Via a Duplex Treatment of Double Glow Plasma Surface Molybdenizing-Laser Surface Texturing (LST)

Dry sliding wear of MA/PM Al-10Ti alloy

Tribological Properties of Ti6Al4V Alloy Composite Texture Fabricated by Ultrasonic Strengthening Grinding and Laser Processing

Microstructure and Sliding Wear Behavior of PM Alloy Al10Ti after Thermal Exposure

Effect of surface oxidation on wear and tribocorrosion behavior of forged and selective laser melting-based TC4 alloys

Combining laser surface texturing and double glow plasma surface chromizing to improve tribological performance of Ti6Al4V alloy

Birth cohort analysis of prevalence of cigarette smoking among Hispanics in the United States.

Effect of Surface Mechanical Attrition Treatment on Surface Topography and Dry Sliding Wear Performance of AA7075‐T6

Wear resistance of NiTi alloy after surface mechanical attrition treatment

Surface strengthening aluminum alloy by in-situ TiC-TiB2 composite coating

In-situ TiB2-TiC reinforced Fe-Al composite coating on 6061 aluminum alloy by laser surface modification

Tailoring Tribological Characteristics in Titanium Alloys by Laser Surface Texturing and 2D Ti3C2Tx MXene Nanocoating

Improving the Wear Resistance Properties of 7A04 Aluminum Alloy with Three Surface Modification Coatings

Investigations on femtosecond laser-induced surface modification and periodic micropatterning with anti-friction properties on Ti6Al4V titanium alloy

Accelerated Formation of Tribo-oxide Layer and Its Effect on Sliding Wear of a Titanium Alloy

Fabrication of Al6061/Ti 3 AlC 2 MAX phase surface composite by friction stir processing and investigation of wear properties

Tribology properties of additively manufactured Ti6Al4V alloy after heat treatment

Study of the microstructure and wear properties of Ti-12Mo-6Zr-2Fe alloy fabricated via selective laser melting