Abstract:The Ni‐PTFE mold is a nanocomposite mold fabricated by one‐pot electroforming using anodic aluminum oxide (AAO) foil as a template. It has low surface energy and low surface wettability, enabling precise, defect‐free nanopatterns down to 100 nm over 20 cycles of thermal nanoimprinting (T‐NIL). UV‐NIL also succeeded, with the nanocomposite mold exhibiting superior demolding compared to a silane‐coated Ni mold. Nanoimprinting large‐area structures, especially high‐density features like meta lenses, poses challenges in achieving defect‐free nanopatterns. Conventional high‐resolution molds for nanoimprinting are often expensive, typically constructed from inorganic materials such as silicon, nickel (Ni), or quartz. Unfortunately, replicated nanostructures frequently suffer from breakage or a lack of definition during demolding due to the high adhesion and friction at the polymer‐mold interface. Moreover, mold degradation after a limited number of imprinting cycles, attributed to contamination and damaged features, is a common issue. In this study, a disruptive approach is presented to address these challenges by successfully developing an anti‐sticking nanocomposite mold. This nanocomposite mold is created through the co‐deposition of nickel atoms and low surface tension polytetrafluoroethylene (PTFE) nanoparticles via electroforming. The incorporation of PTFE enhances the ease of polymer release from the mold. The resulting Ni‐PTFE nanocomposite mold exhibits exceptional lubrication properties and a significantly reduced surface energy. This robust nanocomposite mold proves effective in imprinting fine, densely packed nanostructures down to 100 nm using thermal nanoimprinting for at least 20 cycles. Additionally, UV nanoimprint lithography (UV‐NIL) is successfully performed with this nanocomposite mold. This work introduces a novel and cost‐effective approach to reusable high‐resolution molds, ensuring defect‐reduction production in nanoimprinting.

Making Modified Fluoropolymer Molds for Ultraviolet Nanoimprint Lithography

Uptake and Metabolism of d-Glucose by Neocosmospora vasinfecta E. F. Smith.

Fabrication of Flexible Mold for Hybrid Nanoimprint-Soft Lithography

Sub-50 nm UV-curing nanoimprint based on fluoropolymer, CYTOP, mold

A Sandwiched Flexible Polymer Mold for Control of Particle-Induced Defects in Nanoimprint Lithography

High Resolution Soft Mold for UV-curing Nanoimprint Lithography Using an Oxygen Insensitive Degradable Material

A "thiol-ene" photo-curable hybrid fluorinated resist for the high-performance replica mold of nanoimprint lithography (NIL)

Cross-Linked Polymer Replica of A Nanoimprint Mold at 30 Nm Half-Pitch

Fabrication of Large-Area Nanostructures Using Cross-Nanoimprint Strategy

Fabrication of Nanoimprint Mold by Multilayer Film Deposition Technique

Surface energy-tunable iso decyl acrylate based molds for low pressure-nanoimprint lithography

A Tunable Nanoimprint System to Create New Features

Fluorosilicone as an Omnimold for Microreplication

Scanning probe lithography for nanoimprinting mould fabrication

Hybrid nanoimprint-soft lithography with sub-15 nm resolution.

High fidelity 3D thermal nanoimprint with UV curable polydimethyl siloxane stamps

A Low-Cost Fabrication System for Manufacturing Soft-Lithography Microfluidic Master Molds

Concave Microlens Array Mold Fabrication in Photoresist Using UV Proximity Printing

Toward Defect‐Free Nanoimprinting

Numerical Investigation for the Resin Filling Behavior during Ultraviolet Nanoimprint Lithography of Subwavelength Moth-Eye Nanostructure

UV-based nanoimprinting lithography with a fluorinated flexible stamp