Abstract:Composite ceramics of 0.7BaO center dot 0.3SrO center dot(I-gamma)TiO2 center dot gamma Nb2O5 (BSTN) with coexistence of barium strontium titanate, Ba1-xSrxTiO3 (BST), and strontium barium mobate, SrxBa1-xNb2O6 (SBN) phases were successfully prepared in situ by controlling excess components according to a specially designed formula of 0.7BaO center dot 0.3SrO center dot(1-gamma)TiO2 center dot gamma Nb2O5 and by using a traditional ceramic process. X-ray diffractometry (XRD), scanning electron microscopy (SEM) and energy dispersion spectrometer (EDS) were used to characterize the phase composition, morphology and the micro-area chemical composition of the composite ceramics. The results showed that the SBN tungsten bronze phase appeared and coexisted stably with the BST perovskite phase when the excess content of Nb2O5 was > 6mol%, whereas the BST perovsklite phase formed and coexisted stably with the SBN tungsten bronze phase when the excess content of TiO2 was > 5.3mol%. In the ease of the two phases being equivalent to each other in BSTN composite ceramics, Nb2O5 was hard to be resolved into the perovskite phase, however, a few of TiO2 was easy to be resolved in the tungsten bronze phase. The microstructure of the composite ceramics were consisted of two kinds of grains. The smaller polygonal grains were belonged to the BST phase, and the larger ones to the SBN phase. The coexistence of the two phases inhibited the growth of the BST crystal. The density of microstructure of the composite ceramic was higher than that of both the pure BST and SBN calcined at the same temperature for the same time.

Forming and Sintering of in Situ Alumina Composite with Hydraulic Inorganic Binder

High-Resolution Electron Microscope Observation of Interface Microstructure of A Cast Al-Mg-Si-Bi-Pb(6262)/Al2o3p Composite

Preparation and Properties of Nano BaNb2O6-Al2O3 Ceramic Composites

In situ Preparation of BST(Nb)/SBN(Ti) Composites

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Design, Characterization, and Incorporation of the Alkaline Aluminosilicate Binder in Temperature-Insulating Composites

In Situ Formation of Ce-TZP/Ba Hexaaluminate Composites.

Direct coagulation casting of alumina suspension by high valence counter ions using Ca (IO 3) 2 as coagulating agent

From marble waste to monocarboaluminate binder: role of sodium aluminate composition, calcined clay type, and curing temperature

Fabrication of 6061 aluminium alloy/Al18B4O33(w) composite by using sol-gel alumina binder

Fabrication of carbon fiber reinforced aluminum matrix composites by inorganic binders

Sintering and Composition of a Powder Mixture of Fine Al2O3 and Beta-Sialon Composite Made from Bauxite

Fabrication and Properties of CaAl12O19-Al2O3 Composite Ceramics

Synthesis of Al7075/TiB2-Al2O3 In-Situ Hybrid Composite by Stir Casting Method

Effect of Composite Binder on the Property of Lightweight Bubble Alumina Ceramics

Fabrication and Characterization of Barium Aluminum Silicate-Silicon Nitride Composites

Rapid Densification and Reaction Sequences in Self-Reinforced Y-α-SiAlON Ceramics with Barium Aluminosilicate As an Additive

A novel composite binder design for direct ink writing alumina-based ceramics with enhanced strength at low sintering temperature

New gel-casting process for alumina ceramics based on gelation of alginate

Evaluation of Different Sintering Agents for Binder Jetting of Aluminum Alloy

Fabrication of Alumina Green Body Through Gelcasting Process Using Alginate