Abstract:The titanium matrix composite was produced through a hot compaction process at 1250 °C using the mixture of elemental powders with chemical composition of Ti-5Al-5Mo-5V-3Cr and 2 wt.% addition of boron carbide. The phase analysis via X-ray diffraction method was performed to confirm the occurrence of an in situ reaction between boron carbide and titanium. Then, the wide-ranging microstructural analysis was performed using optical microscopy as well as scanning electron microscopy along with energy-dispersive X-ray spectroscopy and electron backscatter diffraction. Based on this investigation, it was possible to describe the diffusion behavior during hot compaction and possible precipitation capabilities of TiC and TiB phases. Tensile and compression tests were conducted to determine the strength properties. The investigated composite has an ultimate tensile strength of about 910 ± 13 MPa with elongation of 10.9 ± 1.9% and compressive strength of 1744 ± 20 MPa with deformation of 10.5 ± 0.2%. Observation of the fracture surface allowed us to determine the dominant failure mechanism, which was crack propagation from the reaction layer surrounding remaining boron carbide particle, through the titanium alloy matrix. The study summarizes the process of producing an in situ titanium matrix composite from elemental powders and B4C additives and emphasizes the importance of element diffusion and reaction layer formation, which contributes to the strength properties of the material.

Synthesis of Al7075/TiB2-Al2O3 In-Situ Hybrid Composite by Stir Casting Method

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

In situ Al-TiB composite obtained by stir casting

Microstructure and Mechanical Properties of in Situ Synthesised (Tic+tib)/ti-6Al-4v Composites Prepared by Powder Metallurgy

Mechanical Properties and Microstructure of in Situ TiB_2-7055 Composites

Microstructure, Properties and Strengthening Mechanism of Cu-Tib2-Al2o3 Composite Prepared by Liquid Phase In-Situ Reaction Casting

Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method

Preparation, Microstructures and Mechanical Properties of In-Situ TiB2/Al Composites by Mechanical Stirring and Subsequent Ultrasonic Treatment

On the Study of a TiB2 Nanoparticle Reinforced 7075al Composite with High Tensile Strength and Unprecedented Ductility

Strength and Elastic Modulus Enhancement in Mg-Li-Al Matrix Composites Reinforced by Ex Situ TiB2 Particles Via Stir Casting

Particle Dispersion and Mechanical Properties Enhancement of In-Situ TiB2/7050 Al Matrix Composite Via Additive Friction Stir Deposition

A Novel Fabrication Technology of in Situ TiB2/6063Al Composites: High Energy Ball Milling and Melt in Situ Reaction

Tensile Properties of 15wt. %TiB<sub>2</sub>/7055 Composite Fabricated by <i>In Situ</i> Method

Influence of In Situ Titanium Diboride Particulate Reinforcement on Mechanical Properties of Aluminum–Silicon Based Metal Matrix Composites

Microstructure and Tensile Properties of in Situ Synthesized (Tib+tic)/ti-6Al-4v Composites

Tensile properties of 15wt. %TiB2/7055 composite fabricated by in-situ method

Microstructure and Mechanical Properties of Aluminum Matrix Composites Reinforced With In-Situ TiB2 Particles

Investigation of Microstructural, Mechanical and Corrosion Properties of AA7010-TiB2 in-situ Metal Matrix Composite

Microstructure and Mechanical Properties of In Situ Synthesized Metastable β Titanium Alloy Composite from Low-Cost Elemental Powders

Processing of in situ aluminum-matrix composites and controlling of the solidification microstructures