Abstract:In this study, methane/air combustion in a two-zone catalytic alumina pileup-pellets burner with equivalence ratios varying from 0.55 to 0.70 was researched. The catalytic alumina pileup-pellets were designed by directly depositing perovskite LaMn0.4Co0.6O3 on inert alumina pileup-pellets supports. Flame stability limits, pressure drops, flame temperatures, flue gas temperatures, and pollutants emissions of both catalytic and inert burners with different pellet diameters were investigated. The flame stability limits expanded as equivalence ratio or pellet diameter increased. The flame stability limits were also increased by depositing the perovskite catalyst. The pressure drops of catalytic burners were lower than those inert burners in both reaction and cold flows. More uniform axial temperature distributions were obtained for catalytic burners than for inert burners. Flame temperatures and flue gas temperatures were significantly reduced for catalytic burners compared with inert burners, as were pollutants emissions for unburned hydrocarbon (HC), carbon monoxide (CO), and nitrogen oxides (NOX). The HC emissions reduced as either pellet diameter or inlet velocity increased. The HC emissions of catalytic burners (less than 550 ppm) were significantly lower than those inert burners (ranging from 900 to 2750 ppm). The CO emissions of catalytic burners reduced significantly at lower velocities (S < 35 cm/s) and were almost unchanged at a level below 50 ppm, at higher velocities (S > 35 cm/s). The CO emissions of catalytic burners were sensitive to changes in pellet diameters at lower velocities (S < 20 cm/s). The NOX emissions of catalytic burners (less than 2 ppm) were significantly lower than those inert burners (ranging from 4 to 13 ppm). (C) 2015 Elsevier Ltd. All rights reserved.

Research on Catalyst Sintering in Catalytic Burner

Characteristics of Premixed Catalytic Combustion of Nature Gas

Sintering Temperature Effects on SCR Catalyst Characterization and Catalytic Efficiency

Methane/Air Fuel-Rich Combustion in a Catalyst Enhanced Two-Layer Porous Media Burner

COMBUSTION EFFICIENCY INSIDE CATALYTIC HONEYCOMB MONOLITH CHANNEL OF NATURAL GAS BURNER START-UP AND LOW CARBON ENERGY OF CATALYTIC COMBUSTION

Effect of Thermal Property of Materials on Micro-scale Catalytic Combustion for the Micro Combustor

Mechanisms And Applications Of Catalytic Combustion Of Natural Gas

Non-isothermal Thermogravimetric Investigation on Mutual Effect Between Bituminite and Anthracite in Blends for Blast Furnace Injection

Simulation of temperature field of sintering ignition furnace

Effects of Reactant Injection Conditions on Diffusion Combustion of Natural Gas in a Laboratory-scale Combustor

Experimental Investigation on the Mixing Performance of Heating Gas into the Low Temperature Sintering Flue Gas Selective Catalyst Reaction Facilities

Lean Methane Premixed Combustion over a Catalytically Stabilized Zirconia Foam Burner

Experimental and modelling studies of the catalytic combustion of methane

Catalytic Combustion of Premixed Methane/air in a Two-Zone Perovskite-Based Alumina Pileup-Pellets Burner with Different Pellet Diameters

Premixed lean methane/air combustion in a catalytic porous foam burner supported with perovskite LaMn0.4Co0.6O3 catalyst with different support materials and pore densities

In Situ Experimental Study on the Combustion Characteristics of Captured Chars on the Molten Slag Surface

Experimental Study on the Combustion Characteristics of Ultralow-Concentration Methane in Divergent Porous Media Burner

Research on pollutant emissions of catalytic combustion burner of natural gas start-up

Experimental Study on Temperature Variation in a Porous Inert Media Burner for Premixed Methane Air Combustion

Numerical Studies of a Water-cooled Premixed Burner for Low NO x Combustion of Natural Gas

Experimental study of premixed n-heptane/air catalytic combustion characteristics in micro-cylindrical tube