Abstract:OBJECTIVES: Fractographic analysis of indentation cracks is performed following flexure testing as part of the ASTM (1999) standard for fracture toughness, KIc, determination in advanced ceramics. This method depends on the conduciveness of the material towards fractographic interpretation. The purpose of this study was to evaluate the use of fractography in fracture toughness methods with a feldspathic dental porcelain, in which KIc was measured fractographically as well as numerically using two controlled-flaw beam bending techniques.METHODS: The following methods for KIc determination were applied to a dental porcelain containing a leucite volume fraction of 15-20%: (1) surface crack in flexure (SCF) (dependent upon fractographic analysis); and (2) indentation strength (IS) at indentation loads of 9.8 and 19.6 N (applying both standard numeric calculations and fractographic analysis). The testing environments were (1) ambient air (IS and SCF) and (2) flowing dry nitrogen (SCF).RESULTS: No significant differences were found between numeric and fractographic KIc values for the IS technique at both indentation loads (9.8 and 19.6 N) in ambient air, although KIc values were sensitive to indentation load. Due to the presence of residual stresses, stable crack extension was observed fractographically in all IS specimens, as evidenced by differences between initial (ainitial) and critical (acritical) crack dimensions. For the SCF method, there was a significant difference in toughness between specimens tested in air versus dry nitrogen, however no fractographic evidence for chemically assisted slow crack growth (SCG) was observed.SIGNIFICANCE: The SCF method as described by the ASTM standard was applicable to the feldspathic porcelain and produced very comparable results with the numeric toughness calculations of the IS procedure. However, fractographic analysis of the surface crack was somewhat difficult for this glassy ceramic compared with polycrystalline ceramics. Knowledge about stable crack extension or slow crack growth and its fractographic appearance is essential when estimating the toughness from examination of flaw dimensions on fractured surfaces since large calculation errors may occur if these effects are not taken into account.

Comparison of K_(IC) Values for SiC Whisker Reinforced Ceramic Composites Obtained by Using Various Methods

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Assessing fracture toughness in sintered Al2O3–ZrO2(3Y)–SiC ceramic composites through indentation technique

Fracture Behavior of SiC-TiB2 Composite Measured by Different Test Methods

SEVNB Method on Fracture Toughness of Ceramic

Micromechanical characterization of zirconia and silicon nitride ceramics using indentation and scratch methods

Thermal shock resistance of SiC whisker reinforced Si3N4 ceramic composites

Correlation between phase content and mechanical properties of SiCw- ZTA composites sintered by SPS

The Effect of Sintering Additive on Fracture Behavior of Carbon-Whisker-reinforced Silicon Carbide Composites

Fracture Toughness of Advanced Structural Ceramics: Applying ASTM C1421

Mechanical Properties and Toughening Mechanisms of Ceramic Composites

Thermal Mismatch Stress in Sic Whisker Reinforced Aluminium Composite: New Measurement Method by X-Ray Diffraction

Fracture toughness (KIc) of a dental porcelain determined by fractographic analysis

Evaluation by Indentation of Fracture Toughness of Ceramic Materials

The Effects of β-Si<sub>3</sub>N<sub>4</sub> Whisker Content and Orientation on R-Curve Behaviors of Si<sub>3</sub>N<sub>4</sub> Ceramics

Effect of Loading Speed on Fracture Behaviour of ZrO2(Al2O3) Matrix Composites Reinforced with SiC Whiskers

Experimental and Numerical Investigations of Tensile Properties of SiC Particle‐Reinforced Composites

ZrB2 matrix ceramic composites by hot-pressed and SiC whisker reinforced

The properties of the multi-node SiCw and its reinforced Si3N4 ceramic composite material

Study on Microstructures of Micron Si 3 N 4 Composite Ceramic with Addition of Nano SiC and SiC Whisker

The properties of the multi-node SiCw and its reinforced Si 3N4 ceramic composite material