Abstract:The microstructure and mechanical properties of a novel Cr and Si co-alloying Fe–0.6C–15Mn steels, labeled as 2Cr(3Si), 4Cr(3Si), 6Cr(3Si), and 4Cr(0Si), were investigated. All samples for mechanical property test and microstructure analysis were subjected to solution treatment at 1100 °C for 1 h after forging. The results indicate that the microstructure for the 2Cr(3Si), 4Cr(3Si) and 4Cr(0Si) steels mainly consists of the full austenite, and grain size is about 100 μm, whereas the microstructure of the 6Cr(3Si) steel exhibits austenite and some undissolved Cr 7 C 3 carbides. The refined austenite grain size of 48 μm is obtained in 6Cr(3Si) steel. The strength and elongation of the experiment steels with Si and Cr increase significantly with the Cr contents. Among the steels, the 6Cr(3Si) steel has the maximum yield strength, tensile strength and elongation of 490 MPa, 987 MPa and 41.5%, respectively. And the impact toughness is 151 J cm −2 . The Si-free steel (4Cr(0Si)) exhibits a low yield strength (372 MPa) and a high tensile strength (992 MPa). The high elongation of 74.8% and impact toughness of 320 J cm −2 are obtained. The results also demonstrate that the Cr and Si co-alloying in high-Mn steels is beneficial to improve work hardening capability, and the work hardening capability increases with the increase of Cr content. According to the results analyzed by the electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM), the strain-induced ε -martensite is dominant at the low strain level and the content of ε -martensite increases with the increase of the tensile strain. The maximum amount of the ε -martensite is found in the 6Cr(3Si) steel. With the strain increasing, α '-martensite appears in microstructure, which is formed on the ε -martensite. In addition, the stacking faults (SF) and mechanical twins (MT) are also observed.

MicrostructurMicrostructure and Properties and Fracture Surface Analysis of a Mediumcarbon and Medium Cr Wear-Resistant Steel

Study on Microstructure and Wear Behavior of Cr25 Heat Resistant Steel

Microstructure and Mechanical Properties of Chromium-Alloyed Silicon Cast Steel

Coarse Grained Heat-Affected Zone Microstructure and Brittleness of Ti-Nb-B Microalloyed High Toughness and Wear Resistant Steel

Effect of Cr and isothermal holding temperature on microstructure and properties of complex phase steel with high formability (CH steel)

The Microstructure Transformations and Wear Properties of Nanostructured Bainite Steel with Different Si Content

Investigation on Microstructure and Properties of Low‐Carbon Wear‐Resistant Steels with Addition of Cr and Ni

Effect of Annealing Temperature and Time on Microstructure and Mechanical Properties of High Cr Ferritic Casting Steel

A study of the abrasive wear of carbon steels

Analysis of Microstructure and Properties of Commonly Used Molds Steels after Heat Treatment

Microstructure and mechanical behavior of a novel Fe–Mn–C–Cr–Si high-manganese steel

Study on the Microstructures and Fatigue Properties of 1.4 ％C Ultra-High Carbon Steel

Effect of Heat Treatment on Microstructure and Properties of Improved 40crni2si2mov Steel

Quantitative Analysis of Microstructure and Impact Toughness in the Simulated Coarse-Grained Heat-Affected Zone of Cu-bearing Steels

Fracture Characteristic and Strengthening Mechanism of Heat Resistant Steel ZG1Cr10MoWVNbN

Influence of Ni content on impact-abrasion wear resistance of medium-carbon low alloy cast steel

Development and Production of Hsla Wear-Resistant Steel

Effect of Banded Structure on the Cr–Ni–Mo–V Steel High-Temperature Frictional and Wear Performance

A Study of Microstructures and Properties of High‐Carbon Si‐Cr Cast Steel Containing Rare Earth and Titanium

Micro Structure Analysis for Stress Rupture Test Specimens of ZG1 Cr10 MoVNbN Castings

Mechanical Properties and Microstructures of A Novel Low Carbon High-Silicon Martensitic Steel