Abstract:Recently, energy conservation, environmental protection and security are the main factors considered by the automotive manufacturers. Medium-Mn steel with excellent combination of specific strength and ductility have been regarded as the potential candidates for automotive applications. The excellent combination of specific strength and ductility depends on the microstructure under different heat treatment processes of the steels. Therefore, the relationship of the combination of specific strength and ductility and microstructure should be studied in detail. Anew alloy system of aluminum-containing medium-Mn steel was developed in this study. The addition of aluminum stabilizes alpha-ferrite, and facilitates the presence of 6-ferrite during solidification. The addition of Mn and C compensates the effect of aluminum on phase stability and ensures austenite formation. In this investigation, the effects of intercritical annealing temperature on the microstructure and tensile properties of a newly designed cold-rolled aluminum-containing medium-Mn steel (0.2C-5Mn- 0.6Si- 3Al, mass fraction, %) were investigated by SEM, XRD and uniaxial tensile tests. The tensile results show that an excellent combination of ultimate tensile strength (sigma(b)) of 1062 MPa, total elongation (delta) of 58.2% and sigma(b) x delta of 61.8.% could be obtained after annealing at 730 degrees C. The inverted austenite of the cold-rolled steel coarsenes and gradually changes its morphology from mainly lamellar to mainly equiaxed with increasing intercritical annealing temperature, and a duplex microstructure consisting of multi-scale retained austenite could be obtained at 730 degrees C, which possesses suitable mechanical stability and thus presents prolonged transformation-induced plasticity (TRIP) effect during tensile deformation. This kind of sustainable TRIP effect and the cooperative deformation of ferrite are responsible for the superior mechanical properties. The investigation of tensile fracture behavior shows that the nucleation and growth of voids occurred mainly at the interfaces between soft ferrite and hard martensite induced by deformation.

Microstructure and mechanical behavior of a novel Fe–Mn–C–Cr–Si high-manganese steel

Microstructure and mechanical properties of a novel medium Mn steel with Cr and Mo microalloying

Microstructural Evolution and Mechanical Properties of Al0.3CoCrFeNiSix. High-Entropy Alloys Containing Coherent Nanometer-Scaled Precipitates

Stacking fault energy and fcc→hcp transformation driving force in Fe-Mn-C-Cr-Si high manganese steels and experimental investigation

Effects of Si on the Microstructure and Work Hardening Behavior of Fe‒17Mn‒1.1C‒xSi High Manganese Steels

Unveiling the Precipitation Behavior and Mechanical Properties in G-phase Strengthened CrFe2Ni2Ti0.2Six Multi-Principal Element Alloys

Investigation on the microstructural evolution and mechanical properties of partially recrystallized Fe-27Mn-10Al-1.4C steel

Fe–Mn–Si–Cr–Ni Based Shape Memory Alloy: Thermal and Stress-Induced Martensite

Influence of silicon addition on intercritical annealing process and tensile properties of medium Mn steel

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

The Influence of Cr Addition on the Microstructure and Mechanical Properties of Fe-25Mn-10Al-1.2C Lightweight Steel

Microstructure Evolution and Corresponding Mechanism of Al–Si–Mg–Cu Alloy with Addition of Mn/Mn+Cr

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Effect of Si Content on Microstructure and Properties of Low-Carbon Medium-Manganese Steel after Intercritical Heat Treatment

Effect of Fe and Mn Content on the Microstructures and Tensile Behaviour of AlSi7Cu3 Alloy: Thermal Analysis and Tensile Tests

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Effect of annealing time on microstructure and mechanical properties of Fe–C–Mn–Al–Si steel

On the Significance of C and Co on Shape Memory Performance of Fe–Mn–Si–Cr–Ni Shape Memory Alloy

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties

Microstructure evolution of a novel low-silicon cast aluminum alloy modified with Mn and Cr during solution treatment

Microstructure and Mechanical Properties of the 6 wt% Mn-Doped Martensitic Steel Strengthened by Cu/NiAl Nanoparticles