Abstract:The purpose of this research is to investigate the effects of silicon and nano-carbon black (C.Bn), both individually and in combination, on the microstructure and mechanical properties of a three-component HfC–ZrC–TiC composite, which has not been studied until now. Four composites were fabricated with the chemical compositions of HfC–ZrC–TiC, HfC–ZrC–TiC/3 wt% Si, HfC–ZrC–TiC/15 vol% C.Bn, and HfC–ZrC–TiC/3 wt% Si/15 vol% C.Bn using the spark plasma sintering (SPS) method at a temperature of 2000 °C for 25 min under a pressure of 35 MPa. The relative density of the samples was measured using the Archimedes method. Microstructural studies and phase identification were conducted using field emission scanning electron microscopy (FESEM) and X-ray diffraction analysis (XRD), respectively. The results indicated that the addition of silicon and C.Bn, both alone and in combination, enhances densification, achieving a relative density increase from 99.7% in the additive-free sample to full density. XRD analysis revealed that in all samples, Hf, Zr, and Ti elements interdiffuse to form a solid solution. In the sample containing silicon, silicide phases (TiSi2 and HfSi2) were formed. Additionally, in the samples containing C.Bn and silicon, the SiC phase was synthesized in situ at the nanoscale. The highest and lowest hardness values were recorded at 32.1 GPa for the HfZrTi/Si/C.Bn sample and 21.6 GPa for the HfZrTi/Si sample, respectively. The fracture toughness values were 6.5 MPa m 0.5 , 6.1 MPa m 0.5 , 5.8 MPa m 0.5 , and 4.1 MPa m 0.5 for the HfZrTi/3 wt% Si/15 vol% C.Bn, HfZrTi/3 wt% Si, HfZrTi/15 vol% C.Bn, and HfZrTi samples, respectively.

Microstructure Evolution and Properties of Hf/Zr-based UHTCs Modified C/C Composites Prepared by Reactive Melt Infiltration Method

Microstructure and flexural strength of C/HfC-ZrC-SiC composites prepared by reactive melt infiltration method

Microstructure and ablation behavior of C/C–HfC–SiC composites fabricated by reactive melt infiltration with Hf–Si alloy

Microstructure and Ablation Behavior of C/C-SiC-(ZrxHf1−x)C Composites Prepared by Reactive Melt Infiltration Method

Fabrication and characterization of HfCZrCTiC composites: role of carbonaceous and metallic additives

Ablation properties of C/C-UHTCs and their preparation by reactive infiltration of K2MeF6 (Me = Zr, Ti) molten salt

Microstructure and ablation resistance of C/C-HfC-SiC composites prepared by RMI with different powder particle sizes

UHTC coating reinforced by HfC nanowires against ablation for C/C composites

Influences of deposition temperature, gas flow rate and ZrC content on the microstructure and anti-ablation performance of CVD-HfC-ZrC coating

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites

Characterization of carbon fiber-reinforced ultra-high temperature ceramic matrix composites fabricated via Zr-Ti alloy melt infiltration

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Use of Zr–Ti Alloy Melt Infiltration for Fabricating Carbon-Fiber-Reinforced Ultrahigh-Temperature Ceramic Matrix Composites

Construction of sandwich-structured C/C-SiC and C/C-SiC-ZrC composites with good mechanical and anti-ablation properties

Preparation and Microstructure Characterizations of Novel C/C-Zr(Hf)B<sub>2</sub>-Zr(Hf)C-SiC Composites

Sintering behavior and mechanical properties of Ta<sub>4</sub>HfC<sub>5</sub>-based composites with ZrB<sub>2</sub> additive

Effect Of Zrc Amount And Distribution On The Thermomechanical Properties Of C-F/Sic-Zrc Composites

Influence of Reactive Melt Infiltration Parameters on Microstructure and Properties of Low Temperature Derived Cf/ZrC Composites

ZrC Modified Carbon/carbon Composites Using ZrSi2 and Zr-Cu Alloys As Reactive Infiltrating Materials: A Comparative Investigation

Fabrication and properties of Cf/ZrC‐SiC‐based composites by an improved reactive melt infiltration

Microstructure and Ablation Performance of SiC–ZrC Coated C/C Composites Prepared by Reactive Melt Infiltration