Abstract:The purpose of this research is to investigate the effects of silicon and nano-carbon black (C.Bn), both individually and in combination, on the microstructure and mechanical properties of a three-component HfC–ZrC–TiC composite, which has not been studied until now. Four composites were fabricated with the chemical compositions of HfC–ZrC–TiC, HfC–ZrC–TiC/3 wt% Si, HfC–ZrC–TiC/15 vol% C.Bn, and HfC–ZrC–TiC/3 wt% Si/15 vol% C.Bn using the spark plasma sintering (SPS) method at a temperature of 2000 °C for 25 min under a pressure of 35 MPa. The relative density of the samples was measured using the Archimedes method. Microstructural studies and phase identification were conducted using field emission scanning electron microscopy (FESEM) and X-ray diffraction analysis (XRD), respectively. The results indicated that the addition of silicon and C.Bn, both alone and in combination, enhances densification, achieving a relative density increase from 99.7% in the additive-free sample to full density. XRD analysis revealed that in all samples, Hf, Zr, and Ti elements interdiffuse to form a solid solution. In the sample containing silicon, silicide phases (TiSi2 and HfSi2) were formed. Additionally, in the samples containing C.Bn and silicon, the SiC phase was synthesized in situ at the nanoscale. The highest and lowest hardness values were recorded at 32.1 GPa for the HfZrTi/Si/C.Bn sample and 21.6 GPa for the HfZrTi/Si sample, respectively. The fracture toughness values were 6.5 MPa m 0.5 , 6.1 MPa m 0.5 , 5.8 MPa m 0.5 , and 4.1 MPa m 0.5 for the HfZrTi/3 wt% Si/15 vol% C.Bn, HfZrTi/3 wt% Si, HfZrTi/15 vol% C.Bn, and HfZrTi samples, respectively.

Sintering behavior and mechanical properties of Ta<sub>4</sub>HfC<sub>5</sub>-based composites with ZrB<sub>2</sub> additive

Densification, Microstructure and Mechanical Properties of Ta4HfC5-based Ceramics Obtained from Synthesized Nanoscale Powder

Fabrication and characterization of HfCZrCTiC composites: role of carbonaceous and metallic additives

Powder synthesis, densification, microstructure and mechanical properties of Hf-based ternary boride ceramics

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

Improved toughness of HfC with tantalum fibre net and tantalum foil

Effect of Ti Additives on the Sintering Behavior and Mechanical Properties of ZrC-W Composites

Microstructural evolution and mechanical properties of in situ nano Ta4HfC5 reinforced SiBCN composite ceramics

Novel TiC-based composites with enhanced mechanical properties

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

Densification, microstructure and mechanical properties of ZrB2–SiCw ceramic composites

Microstructure and Mechanical Properties of ZrC-TaC Composite Fabricated by Displacive Compensation of Porosity at 1300 °C

Microstructure and Properties of Hot Pressed Zr2(Al(Si))4C5/SiC Composites

Microstructure and Mechanical Properties of HfC-SiC Ceramics Influenced by WC Addition

Phase Formation, Microstructure and Mechanical Properties of TaB2-SiC Composites Synthesized by Reaction Hot Pressing: Effects of SiC Contents and Oxygen Impurity

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

Spark plasma sintering of B4C–ZrB2 and B4C–ZrB2–SiC ceramics

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites

Hardness and toughness improvement of SiC‐based ceramics with the addition of (Hf 0.2 Mo 0.2 Ta 0.2 Nb 0.2 Ti 0.2 )B 2

Microstructure and mechanical behavior of TaxHf1−xC–SiC fabricated by reactive hot‐pressing: Effect of Ta:Hf ratio