Abstract:New Fe82-85B13-16Si1Cu1 amorphous alloys with low B content and high B/Si content ratios were synthesized by melt spinning for developing good soft magnetic and high strength materials. The crystallization occurs through two stages and the first-stage onset temperature increases from 673 K to 705 K with increasing B content, while the second-stage temperature remains nearly constant. The first and second stages are due to the precipitation of the α-Fe(Si) phase with a size of about 30 nm and the decomposition of the remaining amorphous phase to α-Fe(Si)+Fe3B+Fe2B, respectively. The Fe-based alloys exhibited good soft magnetic properties both in annealed amorphous and nanocrystallized amorphous+α-Fe(Si) phases. The saturated magnetic flux density, coercivity and permeability at 1 kHz are 1.7 T, 4.92 A/m and 7100, respectively, for the annealed amorphous 14B alloy and 1.74 T, 5.62 A/m and 10100, respectively, for the nanocrystallized 13B alloy. The Vickers hardness (H v) is 803–867 for the as-spun state and it increases with decreasing B content. The H v increases significantly by crystallization to α-Fe+amorphous phases and reaches 997–1550 for the alloys annealed at 693–763 K just before T x2. The ultrahigh H v is presumably due to the combination of fine nanoscale mixed phases, high volume fraction of α-Fe(Si) without internal defects and the enrichment of B into the remaining amorphous phase. Such ultrahigh H v has not been obtained for Fe-based amorphous and crystallized alloys before and the addition of 1%Cu is essential for the ultrahigh H v and the amorphous phase formation for the Fe-rich 85%Fe alloy. The new Fe-based alloys are encouraging as future soft magnetic and ultrahigh strength materials with low material cost.

(Fe,co)–zr–nd–b Bulk Amorphous Alloys with Good Soft Magnetic Properties

Fe65B22Nd9Mo4 bulk nanocomposite permanent magnets produced by crystallizing amorphous precursors

High-temperature Magnetic Properties of Fe-based Nanocrystalline Alloy

Preparation of FeCo-based amorphous alloys with excellent soft magnetism and high glass transition temperature

Fe-based Bulk Amorphous Alloys with High Glass Formation Ability and High Saturation Magnetization

A unique Fe-based soft magnetic alloy and its magnetic softening mechanism

Fe-B-Si-C-Cu amorphous and nanocrystalline alloys with ultrahigh hardness and enhanced soft magnetic properties

PREPARATION AND PROPERTIES OF BULK AMORPHOUS Fe-Ni-P-B-Ga ALLOYS

Soft magnetic properties of Co-doped FeSiBC amorphous and nanocrystalline alloys

Magnetic Properties and Glass-Forming Ability of Modified Fe–P–Si–B Bulk Amorphous Alloys

Soft magnetic properties of FeCoSiBC amorphous alloys with high saturation magnetization

Ductile Fe-Based Amorphous Alloys with High Iron Content

Nd 5Fe 64B 23Mo 4Y 4 bulk nanocomposite permanent magnets produced by crystallizing amorphous precursors

Nanocrystallization, good soft magnetic properties and ultrahigh mechanical strength for Fe82-85B13-16Si1Cu1 amorphous alloys

Fe-based nanocrystalline FeBCCu soft magnetic alloys with high magnetic flux density

Thermal and magnetic properties of Fe(Co)BCCu amorphous alloys with high saturation magnetization of 1.77 T

Fabrication and Soft Magnetic Properties of Fe–B–Si–Zr/Hf–Cu Nanocrystalline Alloys with High Glass-Forming Ability

High performance Fe-based nanocrystalline alloys with excellent thermal stability

Exceptionally High Saturation Magnetic Flux Density and Ultralow Coercivity Via an Amorphous–Nanocrystalline Transitional Microstructure in an FeCo‐Based Alloy

Bulk Metallic Glass Formation, Composite, And Magnetic Properties Of Fe-B-Nd Based Alloys

Magnetic Characteristics for the Mould-Cast Hard Magnetic Nd70–xFe30Alx ($x=0$ –10) Alloys