Abstract:As a kind of typical human-machine interaction robot,the powered lower-limb exoskeleton driven by hydraulics can augment wearer's power while following wearer.This kind of exoskeleton has a broad application in military field,rescue occasions,and so on,however,there are still many technical difficulties which need to be studied,such as structure optimization.There are 3 kinds of design concepts among the exoskeleton structure design.To guarantee the flexibility and decrease the dead weight of exoskeleton,quasi-anthropomorphic design was adopted,which means the lower-limb exoskeleton is similar to leg but does not need one-to-one match.According to quasi-anthropomorphic design rule,7 degrees of freedom for single leg were set to satisfy the freedom need of wearer.Among these 7 degrees of freedom,only 2 degrees are active which are located in sagittal plane of knee joint and hip joint.During designing the active freedom of knee joint,the core parameters are the size of hydraulic cylinder and the torque which can be produced.So it is significant to study a method which can lead to a minor size of hydraulic cylinder while producing the same torque.To optimize the structure of knee joint and its hydraulic system,the computer aided design (CAD) method and the numerical calculation method were adopted to design the structure of the hydraulic cylinder and its installation position.According to the schematic diagram of structure,the relationship of torque,arm of force,and installation position was built.Design indicators were obtained through analyzing the clinical gait analysis (CGA) data,which was widely used in lower-limb exoskeleton research.To find out the optimized parameter,MATLAB was used to present graphics which depicted the nonlinear relationship which was built before.According to the optimization method,the hydraulic driven knee joint of the lower limb exoskeleton was designed and assembled.During the normal walking phase,there are 2 kinds of torques in knee joint,which contain flexure torque and extension torque.Flexure torque is used to bend shank to avoid the collision of foot and floor while extension torque is used to extend shank to drive the body forward.The both kinds of torques are also important for a person to walk.So simulations were designed to compare the torque produced by hydraulic driven knee joint and the torque needed in normal walking which was got through CGA data.The simulation found that the designed hydraulic driven knee joint could meet the torque demand.Meanwhile,the comparison experiments were also designed and implemented.Hydraulic driven knee joint was driven to follow the motion of wearer in 2 conditions.In the first condition,the wearer just needed to bear the exoskeleton's own weight,which was about 10 kg.In the second condition,another 10 kg load was added on the exoskeleton.It should be noted that all load was transferred to the ground through lower-limb exoskeleton,which meant the added load wouldn't add other burden to wearer.This is the work mechanism of powered lower-limb exoskeleton.In the comparison experiments,the wearer was demanded to move a similar trajectory while it was impossible to move the same trajectory.Experiments showed that the average error was decreased by 0.05％ while the maximum error was increased by 20.7％.Considering the load was increased by 100％ and the motion range was large,these results clear demonstrated how the designed hydraulic driven knee joint satisfied the demand of walking with load.In conclusion,a method is proposed to fulfill the optimization of the knee joint structure of the hydraulic driven lower-limb exoskeleton,and it can obviously instruct other joint design of exoskeleton which is driven by linear actuator such as linear motor and electric cylinder.

Novel Lightweight Lower Limb Exoskeleton Design for Single-Motor Sequential Assistance of Knee & Ankle Joints in Real World

Design an Underactuated Soft Exoskeleton to Sequentially Provide Knee Extension and Ankle Plantarflexion Assistance

A Time Division Multiplexing Inspired Lightweight Soft Exoskeleton for Hip and Ankle Joint Assistance

Design of an Ankle Exoskeleton That Recycles Energy to Assist Propulsion During Human Walking

Design of a Purely Mechanical Sensor-Controller Integrated System for Walking Assistance on an Ankle-Foot Exoskeleton

A Lightweight Ankle Exoskeleton Amplifying Input Power to Create High Power Assistance

Design and Gait Realization of Power-assisted Lower Limbs Exoskeleton

Structure design and experiment of knee joint of hydraulic driven lower-limb power-assistance exoskeleton robot

A Lower Extremity Exoskeleton System for Walking Assist

Cascade Force Control of Lower Limb Hydraulic Exoskeleton for Human Performance Augmentation

An untethered cable-driven ankle exoskeleton with plantarflexion-dorsiflexion bidirectional movement assistance

The Study of Ankle Assisted Exoskeleton

Preliminary Evaluation Of Gait Assistance During Treadmill Walking With A Light-Weight Bionic Knee Exoskeleton

A Novel Design of Unpowered Exoskeleton for Loaded Walking Using Only Hip Abduction Torque

Actuator optimization and deep learning-based control of pediatric knee exoskeleton for community-based mobility assistance

Design and Implementation of a Lower Extremity Exoskeleton for Walking Assist

Modeling and Stiffness-Based Continuous Torque Control of Lightweight Quasi-Direct-Drive Knee Exoskeletons for Versatile Walking Assistance

Design and analysis of a novel 12-DOF self-balancing lower extremity exoskeleton for walking assistance

Development of an individualized stable and force-reducing lower-limb exoskeleton

Design and Control of a Novel Semi-Passive Knee Exoskeleton

Design of a Minimally Actuated Lower Limb Exoskeleton with Mechanical Joint Coupling