Abstract:Background: Robotics is emerging as a promising tool for functional training of human movement. Much of the research in this area over the last decade has focused on upper extremity orthotic devices. Some recent commercial designs proposed for the lower extremity are powered and expensive - hence, these could have limited affordability by most clinics. In this paper, we present a novel un-motorized bilateral exoskeleton that can be used to assist in treadmill training of motor-impaired patients, such as with motor-incomplete spinal cord injury. The exoskeleton is designed such that the human leg will have a desirable swing motion, once it is strapped to the exoskeleton. Since this exoskeleton is un-motorized, it can potentially be produced cheaply and could reduce the physical demand on therapists during treadmill training. Results: A swing-assist bilateral exoskeleton was designed and fabricated at the University of Delaware having the following salient features: (i) The design uses torsional springs at the hip and the knee joints to assist the swing motion. The springs get charged by the treadmill during stance phase of the leg and provide propulsion forces to the leg during swing. (ii) The design of the exoskeleton uses simple dynamic models of sagittal plane walking, which are used to optimize the parameters of the springs so that the foot can clear the ground and have a desirable forward motion during walking. The bilateral exoskeleton was tested on a healthy subject during treadmill walking for a range of walking speeds between 1.0 mph and 4.0 mph. Joint encoders and interface force-torque sensors mounted on the exoskeleton were used to evaluate the effectiveness of the exoskeleton in terms of the hip and knee joint torques applied by the human during treadmill walking. Conclusion: We compared two different cases. In case 1, we estimated the torque applied by the human joints when walking with the device using the joint kinematic data and interface force-torque sensors. In case 2, we calculated the required torque to perform a similar gait only using the kinematic data collected from joint motion sensors. On analysis, we found that at 2.0 mph, the device was effective in reducing the maximum hip torque requirement and the knee joint torque during the beginning of the swing. These behaviors were retained as the treadmill speed was changed between 1-4 mph. These results were remarkable considering the simplicity of the dynamic model, model uncertainty, non-ideal spring behavior, and friction in the joints. We believe that the results can be further improved in the future. Nevertheless, this promises to provide a useful and effective methodology for design of un-motorized exoskeletons to assist and train swing of motor-impaired patients.

Preliminary Evaluation Of Gait Assistance During Treadmill Walking With A Light-Weight Bionic Knee Exoskeleton

BioKEX: A bionic knee exoskeleton with proxy-based sliding mode control

Design and analysis of a passive knee assisted exoskeleton

Design and Gait Realization of Power-assisted Lower Limbs Exoskeleton

Mechatronic Design and Control of a Rigid-Soft Hybrid Knee Exoskeleton for Gait Intervention

Simulation of Exoskeleton ZMP During Walking for Balance Control

Biofusion design and parameter optimization for a novel passive assisted knee exoskeleton robot based on eight-bar mechanism

Simulation-based multi-criteria comparison of mono-articular and bi-articular exoskeletons during walking with and without load

Design and Evaluation of Torque Compensation Controllers for a Lower Extremity Exoskeleton

Biomechanical Effects of Robot Assisted Walking on Knee Joint Kinematics and Muscle Activation Pattern.

Design and analysis of a passive exoskeleton with its hip joint energy–storage

Mitigating Crouch Gait with an Autonomous Pediatric Knee Exoskeleton in the Neurologically Impaired

Novel swing-assist un-motorized exoskeletons for gait training

Modulating Multiarticular Energy during Human Walking and Running with an Unpowered Exoskeleton

Analysis and Evaluation of a Quasi-Passive Lower Limb Exoskeleton for Gait Rehabilitation

Iterative Learning Control for a Soft Exoskeleton with Hip and Knee Joint Assistance

Admittance Control Based Gait Intervention Strategy of Knee Exoskeleton for Stance Phase Support

Mechatronic Design of a Shank-Free Bilateral Exoskeleton for Loaded Walking

A Time Division Multiplexing Inspired Lightweight Soft Exoskeleton for Hip and Ankle Joint Assistance

Biomechanical Design of a Novel Flexible Exoskeleton for Lower Extremities

Adding compliant joints and segmented foot to bio-inspired below-knee exoskeleton