Abstract:In the present work, the objectives were to investigate the type of microstructure and texture that developed after two step cold rolling — continuous annealing. Further, an attempt has been made to correlate the microstructure and texture with mechanical properties. Interstitial free (IF) and interstitial free — high strength (IF-HS) steel sheets which contain almost γ-fiber textures, were subjected to two step cold rolling for different percentage of reduction and further continuously annealed. It was observed that cold rolling strengthened the region of (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations of α-fiber as well as γ-fiber. After continuous annealing, cold rolled γ-fiber as well as (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations transformed to extremely strong new γ-fiber. It was found that at two steps 80% cold rolling -continuous annealing, drawability of IF steel sheet was exceptionally high i.e. around 3.15, whereas for IF-HS steel sheets, it was around 2.7. Although, two steps cold rolling -continuous annealing enhanced percentage elongation and stretchability exceptionally, but it reduced the yield strength substantially. However, ultimate tensile strength was hardly affected. In addition, it is also observed that two steps cold rolling — continuous annealing developed uniform grain size in both the grades of steel sheets.

Effect of Cold Rolling Technology on Drawability of IF Steel

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Microstructural Evolution of IF-steel During Cold Rolling

Effect of Annealing Temperature on Texture of Cold-Rolled IF Steel Rolled from Strip Hot-Rolled in Ferrite Region

Effect of two step cold rolling — continuous annealing on micro-structures, textures and mechanical properties in IF and IF-HS steel sheets

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Increase in Low-Carbon Steel 12GBA Strength and Cold Resistance by a Deformation-Thermal Effect

Effect of Cold Rolling and Cryogenic Treatment on the Microstructure and Mechanical Properties of Fe–32Ni Alloy

Δr of Drawability and the Choice of Cold Reduction

Effect of Cold Rolling Reduction Ratio on Microstructure and Mechanical Properties of Fe–10Mn–4Al-0.4C Steel Containing Δ Ferrite

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Effect of Heavy Warm Rolling on Microstructures and Mechanical Properties of AISI 4140 Steel

Effect of cold rolling reduction on microstructure, mechanical properties, and texture of deep drawing dual-phase (DP) steel

Enhanced ductility of strong cold-rolled ribbed rebar through intermediate frequency induction heat treatment based on recrystallization

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel

Effects Of Electric Field Annealing On Recrystallization Texture And Plastic Strain Ratio (R Value) Of If Steel Sheet

Formation of recrystallization texture and its effect on deep drawability for high-purified ferritic stainless steel by two step cold rolling

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Effect of Double Cold Rolling on Magnetic Property and Microstructure of Non-Oriented High Silicon Steel Sheets Cast by Strip Casting Process

Impact of Cold-Rolling and Heat Treatment on Mechanical Properties of Dual-Phase Treated Low Carbon Steel

Mechanical anisotropic behavior of low-carbon steel processed by asymmetric rolling