Reason Analysis and Treatment of Tripping Accident of High Voltage Standby Transformer

Guoqing Wang

2012-01-01

Abstract:Taking a tripping accident of the high voltage standby transformer of a power plant as example,the reasons of the accident were analyzed,and the response strategy was proposed,which provides reference for treating similar problems.

What problem does this paper attempt to address?

Cause Analysis on Large-Scale Wind Turbine Tripping and Its Countermeasures

Shi-en HE,Xin-zhou DONG

DOI: https://doi.org/10.3969/j.issn.1674-3415.2012.01.023

2012-01-01

Abstract:Several large-scale wind turbine tripping accidents occurred in Jiuquan wind power base in 2011. According to the on-site survey and the oscillogram analysis,the cause of these accidents is the short-circuit fault of electrical equipment and cables in wind farm,which leads to the voltage drops in the farm and system,therefore a large number of wind turbines trip because they do not have the low voltage ride through(LVRT) capability. After the fault is cleared,a large number of wind turbines trip again when the system voltage rises to setting point of overvoltage of wind turbine,because the reactive power compensation device in wind farm step-up substation can not timely regulate the voltage automatically. Accordingly,wind turbine retrofitting and collector system and its protection configuration improvement are put forward from a practical point of view,and combining with the characteristics of large-scale wind power base,the subjects to prevent wind power reasonably from large-scale tripping are also put forward for further research.
Analysis of a 35kV vacuum circuit breaker accident caused by protection misoperation

Chong Wang,Shan Li,Zhongqiang Zhan

DOI: https://doi.org/10.1117/12.2634855

2022-04-25

Abstract:Reactor equipment is widely used in high-voltage backbone power grid, and its reliability directly affects the safe and stable operation of large power grid. In this paper, a 35 kV Vacuum Circuit Breaker breaking shunt reactor accident in a substation is deeply analyzed. Firstly, the protection misoperation is comprehensively analyzed by means of on-site fault characteristics, theoretical simulation calculation and return to plant disassembly inspection. Secondly, by integrating various information and adopting the analysis method of combining theory with practice and combining in plant traceability and test verification, aiming at the defects of the protection device of the substation, technicians and manufacturers comprehensively inspected the protection device and confirmed that there was an error in the background logic of the monitoring device, resulting in the wrong opening signal. After the manufacturer upgraded the monitoring software, the defect was eliminated. Finally, according to the fault causes, the follow-up countermeasures for such faults are put forward.
Analysis on Reason of Generator Set Complete Power Outage of a Hydropower Plant

Yue Yang,Zhan Shu,Yan Zhang,Xin Xie,Bei Cao,Simeng Chang

DOI: https://doi.org/10.1088/1757-899x/452/3/032125

2018-01-01

IOP Conference Series Materials Science and Engineering

Abstract:There was a single-phase high resistance grounding fault on the outgoing line of a 110kV hydropower plant. As a result of the mismatch of protection setting values, misoperations happened outside of the main transformer protection area, which caused generator set complete power outage. This paper used RTDS to carry out simulation analysis on this fault, restored the development process of the fault and figured out the fault reason. Meanwhile, through the investigation and analysis on the configuration status of the main transformer backup protection from high voltage side and the neighborhood transformer protection of 110kV hydropower plants throughout the whole province, we concluded the irrationality of the protection configuration and proposed the solutions to it.
Fault Analysis and Treatment of Partial Discharge in 500 kV Transformer

PENG Fei,CHENG Lin,FANG Tiyou,WU Yihua,ZHAN Hao

DOI: https://doi.org/10.13296/j.1001-1609.hva.2015.12.033

2015-01-01

Abstract:Partial discharge of a 500 kV power transformer seriously exceed under 680 kV in routine ACSD test. After the accident, phased oil sampling analysis is taken to the transformer, the diagnostic tests are carried out after check wiring and test equipment. The oil sample test and analysis results indicated the fault of transformer is internal fault. Subsequently , the high-voltage head hanging core examination reveals the outermost insulation and regulated lead insulation wood screws and other parts have traces of discharge. Through the discharge site and the surrounding electric field simulation analysis , clear the discharge path, combined with experimental phenomena, determines that the failure is caused by a design flaw of the transformer and low dielectric strength of the insulation member caused. The corresponding maintenance treatment program is proposed. The accident analysis and processing programs can provide proposals for improving the follow-up of power transformer design and production process.
Analysis of a 110kV Transformer Near-Area Short-Circuit Fault Resulting in Winding Deformation and Management Measures

Yong Gao,Jie Wang

DOI: https://doi.org/10.1109/SGES59720.2023.10367006

2023-01-01

Abstract:This paper provides some suggestions for the safe, reliable and economic operation of the transformer by studying and analysing a case in which a 110kV transformer was destabilized due to a short-circuit fault in the proximity of the medium voltage side of the transformer, which resulted in the main transformer destabilisation. Firstly, the real cause of the transformer failure is analysed by detailed analysis of the transformer failure process, test and disassembly verification. In addition, by collecting the detailed structural parameter table of the faulty transformer, and further using the self-developed VIT calibration platform system modelling simulation calculation, the actual ability of the transformer to withstand the short-circuit current is not as good as the theoretical withstand value provided by the manufacturer. Finally, for the operating transformers, passive management measures are proposed in terms of irregular short-circuit resistance calibration, segmented operation of medium and low-voltage busbars, neutral point addition of small reactance grounding, addition of current-limiting reactors, and return to the factory (on-site) for overhaul; for the non-networked transformers, proactive management recommendations are proposed in terms of quality control in advance of the network entry, design of the transformer, raw material selection, and requirements of the manufacturing process.
Operational Analysis on 500kv Three Gorges Overhead Power Transmission Line

Youwei Du

2008-01-01

Abstract:Keeping the safety of 500 kV Three Gorges power line,the major electric energy transmission passage,is of great significance to the Three Gorges regional network,as to the nationwide grid too.To reduce the fault tripping rate and to ensure running safety and stability of Three Gorges power line,some precautionary methods were put forward to prevent fault tripping by such as lightning strike,dirty flash,ice covering,wind drifting,etc,on the basis of a statistical analysis to the 500 kV Three Gorges power line's operational data running by Hubei EHV Transmission and Substation Company since 2001,which established the basis for improving power line availability factor,and enhancing running safety and stability of electricity grid.
Analysis and Research on a Burning Accident of Electromagnetic Unit of Capacitive Voltage Transformer

Limin Qu,Chao Wang,Jian Zhang,Leilei Liang,Hang Zhang,Lei Wang,Minhu Xu,Yang Lin

DOI: https://doi.org/10.1109/icmiae57032.2022.00078

2022-01-01

Abstract:Capacitive voltage transformer is an important protection and metering equipment in power system, its reliable and stable operation has an important impact on the safety of power grid, therefore, the research and fault analysis of capacitive voltage transformer is of great significance to ensure the safety of power grid. In this article, an investigation and research on a burning accident of 66kV capacitive voltage transformer electromagnetic unit is carried out, through on-site inspection, principle analysis, electrical test and disassembly inspection, the occurrence process of the accident is deduced, and the specific causes of the accident are obtained. Finally, according to the causes of the accident, targeted preventive measures are given to avoid the recurrence of such accidents, which provides an important reference for the construction technology and fault analysis of the same type of capacitive voltage transformer.
Analysis on Overvoltage in Renovated Control and Protection System for HVDC Power Transmission Project from Tianshengqiao to Guangzhou

Hao Zhou

2011-01-01

Abstract:System overvoltages in the renovated ±500 kV DC power transmission project from Tianshengqiao to Guangzhou under four typical fault conditions,i.e.,single-phase grounding occurred at upper-half rectifier bridge side of wye-wye connected winding of converter transformer,interphase switching surge from AC system,loss of AC power supply occurred at inverter side and inverter being blocked with unblocked bypass pairs,are analyzed and computed to ensure overvoltage at different positions in the grid as well as energy consumption of arresters can be restricted within rational ranges by renovated control and protection system,thus the secure operation of all power equipments can be implemented.Analysis results show that higher overvoltages will appear at neutral-bus due to single-phase grounding occurred at valve side of wye-wye connected winding of converter transformer,and the energy consumption of neutral-bus arrester will also be higher;higher overvoltage will appear at the terminals of rectifier valves due to interphase switching surge from AC system and it makes valve arrester operated;higher overvoltage will occur at AC bus of inverter station due to the loss of AC power supply at inverter side and it makes AC bus arrester operated;a rather high overvoltage will appear on DC polar line at inverter side due to inverter being blocked with unblocked bypass pairs and it makes a high energy consumption of arrester of DC polar line.The energy consumption of all arresters does not yet exceed the designed discharging capability under these four fault conditions,thus secure and stable operation of all arresters can be ensured.
Fault Diagnosis and Analysis of a 110 Kv Transformer

Yong Gao,Jie Wang

DOI: https://doi.org/10.1088/1742-6596/2728/1/012052

2024-01-01

Journal of Physics Conference Series

Abstract:Abstract This paper aims to provide valuable insights and assistance for ensuring the safe operation of a 110 kV main transformer by conducting an in-depth analysis of tap changer breather oil leakage defects. By employing transformer testing, disassembly analysis, and other methods, this study successfully identifies and prevents the possibility of transformer failure. The analysis reveals that the deformation of the transformer winding is caused by insufficient short-circuit resistance, which leads to the deformation of the medium-voltage windings under the continuous action of electrodynamic forces during near-area short-circuit currents. Near-area short-circuits are a significant contributing factor to transformer failures. Therefore, it is recommended to enhance operation and maintenance management for older main transformers and optimize protection settings to reduce the risk of near-area short-circuit failures, thus ensuring the safe and stable operation of the main transformer.
Analysis of explosion on 35 kV voltage transformer in 500kV substation

Dong Ji-min

2008-01-01

Abstract:This paper deals with the process of a multiple fault occuring on non-earthed neutral system, which originates from two-phase grounding fault and non-fault phase voltage rising simultaneously, thus causing arc-grounding overvoltage and probably driving the voltage transformer saturated, resulting in ferro-resonance. In this paper, based on actual fault wave-form recorded data on a 500 kV substation and phasor analysis, the type of the fault and the causes of 35kV PT explosion are analyzed in a quite clear and effective way. Furthermore, measures are proposed to prevent such faults. Fault investigation on the spot shows that the analysis in this paper is valid and enables substation operator to identify such faults quickly and avoid serious consequences.
Research on lightning intruding waves in 220 kV GIS substation

Deng Xu,Zhou Hao

DOI: https://doi.org/10.1109/APL.2011.6110136

2011-01-01

Abstract:The lightning intruding waves in 220 kV GIS substation model was built by using ATP-EMTP software, calculate the lightning over-voltages on electric equipment in substation with different running modes, different grounding resistance and lightning shielding failure. The results show that the maximum over-voltage on electric equipment happened in single bus with single transformer; The smaller the grounding resistance, the smaller the over-voltage value on electric equipment in substation; the lightning shielding failure will not cause harm to substation. Finally, this paper used statistical methods to calculate the years of the safe operation of the substation. It is concluded that the safe running times of substation can meet the requirement when arresters were installed at the incoming lines and the entrance of transformer.
Fault Analysis And Simulation Of Ground-Fault Accident On Transformer In 500 Kv Ac/Dc Grids

Bo Zhang,Ping Lu,Jinjiao Kong,Rui Liu,Quanliang Cao,Hongbo Shao,Wanting Deng,Jun Chen

DOI: https://doi.org/10.3233/JAE-180082

2019-01-01

International Journal of Applied Electromagnetics and Mechanics

Abstract:An actual occurred ground-fault accident of 500 kV transformers in HVDC converter station is presented. A 2D transient electromagnetic-thermal-mechanical finite-element coupling model of 500 kV transformer is developed to analyze the transient process of failure, with consideration of the resistance-temperature relationship and plasticity displacement in the windings' thermal and mechanical characters. To verify the proposed finite-element model, the model is calibrated by pre-fault field test of the transformer in steady state, which shows good agreement with measurement. The short-circuit current adopted in simulation is based on actual on-site measurement of the ground-fault accident. By using the proposed model, simulation results reflect the transient process and explain the post-fault inspected damage well in term of over burn regions in thermal analysis and deformation tendency in mechanical analysis when compared with field post-fault inspection photos.
Analysis on Failure Cause of Plant Test for 500kv Auto-transformer

ZHUANG Yan-fei,YUAN Hai-yan,XIAO Deng-ming,JING Wei,ZHANG Jin-gang

DOI: https://doi.org/10.3969/j.issn.1009-9239.2007.04.006

2007-01-01

Abstract:500 kV auto-transformers are one of the key equipments that play a very important role in power transmission system.Its quality is of great moment on the system safety operation.The factors that influence the insulating properties of auto-transformers are analyzed and a reasonable solution is proposed.
220Kv Transmission Line Fault Diagnosis and Analysis

Chen Zhang,Lixing Zhou

DOI: https://doi.org/10.1109/isdea.2012.604

2012-01-01

Abstract:With the development of power system, reliability and stability of transmission lines requires a gradual increase, particularly pays great attention over voltage protection, but each year, the system still occur more accidents and obstacles because of various over-voltage, the largest proportion of fault lightning trip, this paper analyzes the lighting trip accident with the 220kV ShaLi transmission line, based on field data collection and analysis of this fault, explore and study the causes of lightning over-voltage in power system and propose countermeasures to prevent similar accidents.
Analysis and research on breakdown cause of lightning arrester at low voltage side of 220kV transformer

Limin Qu,Tong Li,Chao Wang,Jian Zhang,Dewen Zhang,Hang Zhang,Mingchen Gong

DOI: https://doi.org/10.1088/1742-6596/2247/1/012045

2022-04-01

Journal of Physics: Conference Series

Abstract:Abstract This paper describes an event of zinc oxide arrester breakdown at low voltage side due to single-phase grounding at medium voltage side of 220kV transformer. Combined with the system wiring mode, equipment damage, system background and test data, the causes of fault and the transmission mechanism of overvoltage are studied in detail, It is concluded that the single-phase grounding short circuit on the medium voltage side leads to the displacement voltage of the neutral point, and the overvoltage is transmitted to the low voltage side through the capacitive coupling between the transformer windings, resulting in the breakdown of the arrester. The correctness of the conclusion is verified by calculation, and reasonable rectification measures and suggestions are put forward to effectively limit the generation of overvoltage on the low-voltage side of the transformer and ensure the safe and stable operation of the power grid.
Analysis on mechanism and preventing strategies of cascading tripping out of numerous wind turbines in China

Duo Xu,Wei Hu,Feng Gao,Xuehong Yang

DOI: https://doi.org/10.1109/POWERCON.2014.6993711

2014-01-01

Abstract:With the integration of large-scale wind power, cascading tripping out of numerous wind turbines has been a serious threat to the security of power grid. This paper discusses the failure mechanism of cascading trips, and focuses on the strategies to prevent this kind of failure. Firstly, the typical development process of the failures has been analyzed. Furthermore, based on the topology structure and parameters of an actual power grid in China, the cascading trip-off failure has been simulated. According to the failure mechanism and characters, two optional voltage control strategies, have been presented. The computer simulation has been carried to verify the validity of the proposed strategies.
Diagnosis and Analysis of the Transformer Winding Deformation Fault

Li Xinyu,Wang Qinghao,Liu Peng,Pang Yanjun,Li Simin,Li Yan,Zhang Ning,Wang Enlu,Lin Bin,Yue Yangzhuo,Liu Chenyang,Liu Qiang

DOI: https://doi.org/10.2991/isrme-15.2015.417

2015-01-01

Abstract:Together export transformer short-circuit accident analysis for a 66kV substation, analyze a variety of test methods 66kV transformer winding deformation, and the advantages and disadvantages of these test methods are discussed in detail, based on capacitance changes proposed transformer winding and with the frequency response method and short-circuit impedance, chromatographic analysis to accurately determine whether the transformer winding deformation methods.
Analysis and Treatment of Voltage Abnormality in a 500 Kv Capacitor Voltage Transformer

丁涛,陈卓娅,刘忠,高利明

DOI: https://doi.org/10.3969/j.issn.1674-1757.2010.02.013

2010-01-01

Abstract:This paper simply introduces a fault of secondary voltage abnormality in a 500 kV capacitor voltage transformer after operation,analysis based on the structure and operation principle of CVT,and the reason is improper installation of capacitor units of capacitive divider in CVT.Fault eliminates and voltage signals indicate properly after regulation for capacitor units on site.At the same time,advisable suggestions propose for installation and commissioning of CVT before operation.
Analysis and Solution to a 126 kV GIS Equipment Fault

SUN Zhuo,XUE Yuan,GUO Hong-wei

2010-01-01

Abstract:This paper introduced the occurrence,the cause of misconduct and the consequence of a 126 kV GIS equipment fault.The real cause of the fault was analyzed,and some problems in dealing with the fault were pointed out.Consequently,some notable factors in the processes of ordering,manufacturing,daily operation management,and fault analysis for the GIS equipment were concluded to guarantee its safe operation.
Test and Fault Analysis for High Power High Frequency High Voltage Transformer

Yan-an WANG,Deng-ming XIAO,You-huai LI,Jin GU,Gui-wen CHEN

DOI: https://doi.org/10.13336/j.1003-6520.hve.2009.05.024

2009-01-01

Abstract:In order to analyze the fault reason of a high power high frequency high voltage transformer, a test platform was established, zero-load test and wave-recording of a fault transformer and a normal transformer were carried out, and the wave characteristic was analyzed. Taking combination of the insulation structure of the transformer, an equivalent circuit of the transformer considering distribution parameters was put forward, and a simplified equivalent circuit was put forward. First, the fault reason which may lead to growth of inputting zero-load current of the transformer is stray capacitances other than air gap abnormity. Second, through the method of current wave comparing, the conclusion that the transformer fault is caused by the insulation breakdown of high voltage winding can be drawn. The diagnosis result is authenticated through the observation after dismantlement of the transformer.

Reason Analysis and Treatment of Tripping Accident of High Voltage Standby Transformer

Cause Analysis on Large-Scale Wind Turbine Tripping and Its Countermeasures

Analysis of a 35kV vacuum circuit breaker accident caused by protection misoperation

Analysis on Reason of Generator Set Complete Power Outage of a Hydropower Plant

Fault Analysis and Treatment of Partial Discharge in 500 kV Transformer

Analysis of a 110kV Transformer Near-Area Short-Circuit Fault Resulting in Winding Deformation and Management Measures

Operational Analysis on 500kv Three Gorges Overhead Power Transmission Line

Analysis and Research on a Burning Accident of Electromagnetic Unit of Capacitive Voltage Transformer

Analysis on Overvoltage in Renovated Control and Protection System for HVDC Power Transmission Project from Tianshengqiao to Guangzhou

Fault Diagnosis and Analysis of a 110 Kv Transformer

Analysis of explosion on 35 kV voltage transformer in 500kV substation

Research on lightning intruding waves in 220 kV GIS substation

Fault Analysis And Simulation Of Ground-Fault Accident On Transformer In 500 Kv Ac/Dc Grids

Analysis on Failure Cause of Plant Test for 500kv Auto-transformer

220Kv Transmission Line Fault Diagnosis and Analysis

Analysis and research on breakdown cause of lightning arrester at low voltage side of 220kV transformer

Analysis on mechanism and preventing strategies of cascading tripping out of numerous wind turbines in China

Diagnosis and Analysis of the Transformer Winding Deformation Fault

Analysis and Treatment of Voltage Abnormality in a 500 Kv Capacitor Voltage Transformer

Analysis and Solution to a 126 kV GIS Equipment Fault

Test and Fault Analysis for High Power High Frequency High Voltage Transformer