Abstract:In this study, a yttria-stabilized zirconia (YSZ) ceramic matrix abradable sealing coating named 8YSZ-5 was successfully prepared by mixed solution precursor plasma spraying, and its thermal shock behavior was studied in detail. During the thermal shock cycles, the microstructure, residual stress and phase stability of the 8YSZ-5 coating were examined by using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) technique. The results show that the 8YSZ-5 coating has excellent thermal shock resistance through a 200-cycle thermal shock test at 1150 degrees C. During the thermal shock cycles, the spallation only existed in a small scale in the edge of the 8YSZ-5 coating, and the coating always maintains a stable phase composition of tetragonal structure. The residual stress study shows that the in-plane residual stress of the 8YSZ-5 coating is detected to be compressive stress, which increases with increasing the thermal shock cycles. The microstructure analysis shows that as the thermal shock test progresses, the number of the pores in the coating gradually decreases due to their spontaneous closure and the average size of the grains gradually increases. The mechanical properties investigation shows that the hardness and surface friction coefficient of the 8YSZ-5 abradable sealing coating increase gradually, while the bond strength of the coating decreases by 50% after 200 thermal shock cycles. The implications of this study are important for the design of advanced abradable sealing coatings prepared by the mixed solution precursor plasma spraying technology.

Phase transitions and microstructure evolutions of in-situ YSZ-ZrC composite coating under long-time plasma torch ablation

Phase and microstructure evolutions of in-situ ZrC composite coating under plasma torch ablation

Multi-cycle and long-term ablation behavior of Cf/ZrB2-SiC composites at 2500 °C

Phase, microstructure and property evolutions of reactively synthesized YSZ-ZrC composite coating based on the content regulation of the precursor

Preparation and Flame Ablation Resistance of Al/Zn/Cu-Incorporated Yttria Partially Stabilized Zirconia Coating

Ablation performance of C/C-ZrC-SiC composites with in-situ YSi 2 -doped ZrC-SiC-ZrSi 2 coating under oxyacetylene torch

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Microstructure Evolution and Failure Mechanism of Cr-coated Zry-4 in Air and Steam at 1200 °C

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Preparation and Characterization of YSZ Abradable Sealing Coating Through Mixed Solution Precursor Plasma Spraying

Study on Thermal Shock Behavior of YSZ Abradable Sealing Coating Prepared by Mixed Solution Precursor Plasma Spraying

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Ablation behavior of C f /ZrC–SiC ultra–high temperature ceramic composites in oxyacetylene torch and plasma wind tunnel

Long-term and cyclic ablation behavior of La2O3 modified Cf/ZrB2-SiC composites at 2500 °C

Enhanced ablation resistance of ZrC–ZrO2 nanocomposite ceramic coating on TiAlNb medium-entropy alloy prepared by a novel strategy

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

Cyclic ablation behavior of C/C–ZrC–SiC composites under oxyacetylene torch

Ablation behavior of ZrC-SiHfOC-MoSi 2 coating for carbon/carbon composites under Ar-O 2 plasma flame