Abstract:The inherent phase instability of the state-of-the-art 7–8 mol% partially stabilised Yttria-Stabilised Zirconia (YO 1.5 , 8 YSZ, tetragonal) under a molten CMAS attack lacks the technological readiness needed to increase the gas inlet temperatures for more thermally efficient gas turbine engines. In this study, the concentration of Yttria in YSZ was systemically increased to impart CMAS resistance and their applicability via emerging Suspension Plasma Sprayed (SPS) coatings and Spark Plasma Sintered (SpPS) pellets under simulated conditions was evaluated. The fully stabilised higher Yttria YSZ compositions (21.4 mol% and 50.2 mol%, cubic) severely restricted the CMAS infiltration and interaction areas, with the later composition forming an apatite layer and the trans-granular cracking and chipping of YSZ into layers reduced with an increase in Yttria content. However, their application into water-based SPS coatings resulted in a complete coating failure following the high-temperature CMAS tests. During Furnace Cycling Test (FCT) tests, the 8 YSZ coating survived 34 thermal cycles compared to just one on the 50.2 mol% YSZ coatings. The premature delamination of the higher Yttria coating seems to have been caused by the spallation associated with horizontal cracks within the coating. The YSZ composition could be modified into CMAS-resistant chemistry; however, their applicability as a functioning TBC with inherent microstructural features, such as the Dense Vertically Cracked (DVC) coating strategy examined in this study, requires new coating design strategies that impart sustainable thermal cycling performance.

Phase, microstructure and property evolutions of reactively synthesized YSZ-ZrC composite coating based on the content regulation of the precursor

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Phase transitions and microstructure evolutions of in-situ YSZ-ZrC composite coating under long-time plasma torch ablation

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Preparation and Characterization of YSZ Abradable Sealing Coating Through Mixed Solution Precursor Plasma Spraying

Phase and microstructure evolutions of in-situ ZrC composite coating under plasma torch ablation

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Phase Transformation Behavior in Air Plasma Sprayed Yttria Stabilized Zirconia Coating

Microstructure and properties of in-situ ZrB2-ZrC composite coatings by plasma spraying

Synthesis of In Situ ZrB2-SiC-ZrC Coating on ZrC-SiC Substrate by Reactive Plasma Spraying

Preparation and Flame Ablation Resistance of Al/Zn/Cu-Incorporated Yttria Partially Stabilized Zirconia Coating

A Study on YSZ Abradable Seal Coatings Prepared by Atmospheric Plasma Spray and Mixed Solution Precursor Plasma Spray

Reactive deposition of CYSZ coatings using PS-PVD technology

Study on Thermal Shock Behavior of YSZ Abradable Sealing Coating Prepared by Mixed Solution Precursor Plasma Spraying

Microstructures and Phases of Ytterbium Silicate Coatings Prepared by Plasma Spray-Physical Vapor Deposition

Microstructure and tribological properties of laser cladded TiAlSi composite coatings reinforced by yttria-stabilized zirconia

Influence of Yttria content in YSZ: An evaluation of water-based SPS coatings and spark plasma sintered pellets

Influence of Y2O3 Doping on Phase Evolution and Dielectric Characteristics of ZrO2 Ceramics

Evolution of Microstructure, Thermophysical and Mechanical Properties and Wetting Behavior of Plasma-Sprayed Yb2O3 and Y2O3 Co-Stabilized ZrO2 Coatings During High-Temperature Exposure and CMAS Corrosion

High temperature oxidation resistance of Y2O3 modified ZrB2-SiC coating for carbon/carbon composites

Study of microstructure, electronic structure and thermal properties of Al2O3-doped tetragonal YSZ coatings