Abstract:Semisolid metal (SSM) processing has become an important industry forming process. Now, the traditional casting or forging alloys cannot show all advantages of semisolid metal processing. Especially, the magnesium alloys currently used in SSM processing are restricted to a few commercial alloys such as AZ91, AM50 and AM60. Therefore, in order to vary semisolid alloys, a new Mg–10Al–4Zn alloy is designed on the basis of conventional AZ91D alloys in this paper. The microstructure evolution and rheological parameter of semisolid Mg–10Al–4Zn alloy was investigated. The microstructure of casting consists of α-Mg and β-Mg17Al12. After compressed by a ratio of 40% in height at the temperature of 210°C, the microstructure of Mg–10Al–4Zn alloy changed from developed dendrites to near-equiaxed grains, and all the dendrites oriented in the same orientation. Whereafter, fine recrystallization grains were formed by the release of the stored fault energy induced by deformation at the elevated temperature. The Mg17Al12 phase containing zincum firstly melted between boundaries of the primary grains and then penetrated into recrystallization grain boundaries, which resulted in the separation of the fine primary grains suspending in liquid phase. The partially melting was discussed through analyzing the phase transformations. In addition, the research on rheological parameters such as solid fraction, the particle size, the spherical degree, and the distribution of liquid phase showed that the Mg–10Al–4Zn alloy had a good semisolid performance.

Microstructure and Mechanical Properties of Semi-Solid Die Casting Mg–5Zn–2Gd–0.6Zr Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Semisolid Die-Casting Process of Mg-20Al-0.8Zn Magnesium Alloy

Microstructure and Properties of Mg-5Al-1.5Ca-0.4Zn Based Alloyby Semi-Solid Isothermal Heat-Treatment-die-pressure-casting Process

Study on Microstructures and Mechanical Properties of Die Casting Mg-xGd-3Y-0.5Zr Alloys

Microstructure and mechanical properties of Mg-Gd-Y-Zn-Zr alloy prepared by rheo-diecasting

Study on the microstructure evolution and rheological parameter of semisolid Mg–10Al–4Zn alloys

Microstructure and mechanical properties of Mg-12Gd-5Y-1Sm-0.5Zr alloy

Microstructure and properties of Mg-9Gd-4Y-1Zn-0.5Zr alloy

Microstructure and Mechanical Properties of Mg-2.6Sm-1.3Gd-0.6Zn-0.5Zr Alloy

Microstructure and Mechanical Properties of Sand Mold Cast Mg–4.58Zn–2.6Gd–0.18Zr Magnesium Alloy after Different Heat Treatments

Study on Semisolid Rheo-Diecasting Process, Microstructure and Mechanical Properties of Mg-6Al-1Ca-0.5Sb Alloy with High Solid Fraction

Microstructure and Mechanical Properties of Large-Scale Mg-Gd-Y-Zn-Mn Alloys Prepared Through Semi-Continuous Casting

Effect of gadolinium on microstructure and the mechanical properties of Mg-Zn-Zr cast magnesium alloys

Effect of Microstructure on Tensile and Fatigue Properties of Cast Mg–10Gd–2Y–0·5Zr Alloy

Microstructure and Strengthening Mechanism of High Strength Mg–10Gd–2Y–0.5Zr Alloy

Microstructure and Mechanical Properties of Mg–3.0Y–2.5Nd–1.0Gd–x Zn–0.5Zr Alloys Produced by Metallic and Sand Mold Casting

Microstructure Evolution During Heat Treatment and Mechanical Properties of Mg–2.49Nd–1.82Gd–0.19Zn–0.4Zr Cast Alloy

Effect of Zn Addition on Microstructure and Mechanical Properties of Mg–9Gd–3Y–0.5Zr Alloy