Abstract:Non-grain oriented electrical steels (NGOES) are typically used in electric applications with rotating magnetic fields and thus essential for the production of electric motors. The increasing number of electric vehicles results in a growing demand for electrical steel sheets used in the stacked laminations of rotor and stator components. E-mobility applications require the best possible magnetic properties for optimum performance and efficiency, especially at high frequencies. In addition, increased mechanical strength is necessary to withstand the centrifugal forces resulting from high revolution speeds. Chemical composition, microstructure and crystallographic texture strongly influence the magnetic properties, whereas the mechanical properties are mainly affected by the chemical composition and grain size. Optimizing the texture is a possible method for improving the magnetic properties without significantly compromising the mechanical strength. In this work a special processing route for the production of 3.25% Si NGOES sample material has been studied, using laboratory cold rolling and annealing facilities. Compared to the classical processing route of single stage cold rolling and annealing, this alternative method involves two cold rolling steps with an intermediate annealing treatment between the first and second rolling sequence and a final annealing treatment after the second rolling step. The samples were produced with different intermediate thicknesses, changing the amount of cold rolling deformation of each sample variation. The degree of deformation affects the recrystallization and grain growth behavior and thus the resulting microstructure and texture. The microstructural and textural evolution was investigated in the hot rolled, intermediate annealed and final annealed state using electron backscatter diffraction (EBSD). Finished samples were additionally examined using magnetic testing and tensile testing. The results indicate a correlation between the intermediate thickness and the final grain size of the steel samples. Furthermore, the highly grain size dependent mechanical strength and magnetic losses are influenced. EBSD-data were used to interpret the texture and to calculate a parameter describing the magnetic quality of the texture. The results show a strong improvement of magnetically favorable texture components along with increasing intermediate thickness, enabling significantly better polarization values in rolling direction and transversal direction. However, anisotropy of the magnetic properties increases as well due to the textural changes.

Microstructure and Texture Development in a Thin Gauge Non Oriented Electrical Steel

The effect of grain size before cold rolling on the magnetic properties of thin-gauge non-oriented electrical steel

Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting

Microstructure and texture evolution of ultra-thin high grade non-oriented silicon steel used in new energy vehicle

Microstructural and textural evolution of double stage cold rolled non-grain oriented electrical steel

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

Texture evolution in grain-oriented electrical steel during hot band annealing and cold rolling

Microstructure and texture evolution of ultra-thin grain-oriented silicon steel sheet fabricated using strip casting and three-stage cold rolling method

The Early Stage Formation of Shear Orientations and the Stability of //ND Orientations During Hot Rolling in Electrical Steels

The significance of hot rolled microstructure controlled by fine-tuning Al content to texture evolution and magnetic properties of low silicon non-oriented electrical steels

The origin of {113} grains and their impact on secondary recrystallization in producing ultra-thin grain-oriented electrical steel

Ultrathin-gauge high silicon non-oriented electrical steel with high permeability and low core loss fabricated by optimized two-stage cold rolling method

Role of Annealing Time in Thin-Gauge Non-oriented Silicon Steels Processed by Strip Casting

Microstructure & Texture Evolution and Magnetic Properties of High Magnetic-Induction 6.5% Si Electrical Steel Thin Sheet Fabricated by A Specially Designed Rolling Route

Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel

EFFECT OF COLD ROLLING PROCESS ON TEXTURE EVOLUTION OF GRADIENT MICROSTRUCTURE IN Fe-3,0 % Si NON-ORIENTED SILICON STEEL

Effect of annealing temperature on magnetic and mechanical properties of twin-roll strip casting Cu-bearing non-oriented electrical steel

Effects by the microstructure after hot and cold rolling on the texture and grain size after final annealing of ferritic non-oriented FeSi electrical steel

Microstructure, texture and magnetic properties of strip-cast 1.3% Si non-oriented electrical steels

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Effect of Grain Size Before Cold Rolling on Microstructure, Texture and Magnetic Properties of Ultra-Thin Low-Si Non-oriented Silicon Steel