Abstract:Non-grain oriented electrical steels (NGOES) are typically used in electric applications with rotating magnetic fields and thus essential for the production of electric motors. The increasing number of electric vehicles results in a growing demand for electrical steel sheets used in the stacked laminations of rotor and stator components. E-mobility applications require the best possible magnetic properties for optimum performance and efficiency, especially at high frequencies. In addition, increased mechanical strength is necessary to withstand the centrifugal forces resulting from high revolution speeds. Chemical composition, microstructure and crystallographic texture strongly influence the magnetic properties, whereas the mechanical properties are mainly affected by the chemical composition and grain size. Optimizing the texture is a possible method for improving the magnetic properties without significantly compromising the mechanical strength. In this work a special processing route for the production of 3.25% Si NGOES sample material has been studied, using laboratory cold rolling and annealing facilities. Compared to the classical processing route of single stage cold rolling and annealing, this alternative method involves two cold rolling steps with an intermediate annealing treatment between the first and second rolling sequence and a final annealing treatment after the second rolling step. The samples were produced with different intermediate thicknesses, changing the amount of cold rolling deformation of each sample variation. The degree of deformation affects the recrystallization and grain growth behavior and thus the resulting microstructure and texture. The microstructural and textural evolution was investigated in the hot rolled, intermediate annealed and final annealed state using electron backscatter diffraction (EBSD). Finished samples were additionally examined using magnetic testing and tensile testing. The results indicate a correlation between the intermediate thickness and the final grain size of the steel samples. Furthermore, the highly grain size dependent mechanical strength and magnetic losses are influenced. EBSD-data were used to interpret the texture and to calculate a parameter describing the magnetic quality of the texture. The results show a strong improvement of magnetically favorable texture components along with increasing intermediate thickness, enabling significantly better polarization values in rolling direction and transversal direction. However, anisotropy of the magnetic properties increases as well due to the textural changes.

Effects by the microstructure after hot and cold rolling on the texture and grain size after final annealing of ferritic non-oriented FeSi electrical steel

Effects of rolling temperature on microstructure, texture, formability and magnetic properties in strip casting Fe-6.5wt% Si non-oriented electrical steel

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

The effect of grain size before cold rolling on the magnetic properties of thin-gauge non-oriented electrical steel

Tracing the recrystallization of warm temper-rolled Fe–6.5 wt% Si non-oriented electrical steel using a quasi in situ EBSD technique

Effect of rolling process on magnetic properties of Fe-3.3 wt% Si non-oriented electrical steel

Improving magnetic properties of non-oriented electrical steels by controlling grain size prior to cold rolling

Microstructural and textural evolution of double stage cold rolled non-grain oriented electrical steel

Effect of Annealing Temperature and Time on the Magnetic Properties and Magnetic Anisotropy of a Temper-Rolled, Semi-processed Non-oriented Electrical Steel

EFFECT OF COLD ROLLING PROCESS ON TEXTURE EVOLUTION OF GRADIENT MICROSTRUCTURE IN Fe-3,0 % Si NON-ORIENTED SILICON STEEL

Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel

A comprehensive study on texture evolution and recrystallization mechanism of Fe-4.5 wt% Si with strong {114}

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

Texture Evolution during Recrystallization and Grain Growth in Non-Oriented Electrical Steel Produced by Compact Strip Production Process

Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting

Dependence of recrystallization behavior and magnetic properties on grain size prior to cold rolling in high silicon non-oriented electrical steel

Effect of recrystallization annealing temperature on microstructure, texture and magnetic properties of non-oriented silicon steel produced by strip casting

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Effect of Grain Size Before Cold Rolling on Microstructure, Texture and Magnetic Properties of Ultra-Thin Low-Si Non-oriented Silicon Steel

Effects of Warm Temper Rolling on Microstructure, Texture and Magnetic Properties of Strip-Casting 6.5wt% Si Electrical Steel