Abstract:Thermoelectric (TE) energy conversion technology provides a promising way to improve the efficiency of fossil energy by generating electricity from low-grade waste heat. With regard to these applications, thermoelectric generators (TEGs) should be designed from system integration perspectives to simultaneously improve heat transfer efficiency and system simplification as well as the robust mechanical properties. However, typical TEGs fabricated by conventional methods barely accomplish such requirements. Herein, high-quality TEGs were assembled by combining the well-flowable spherical bismuth telluride (BT) powdered precursors and selective laser melting (SLM) technology. By optimizing the electronic and phonon transport properties through defect engineering driven by 3D printing, a high figure of merit was accomplished for 1.27 (p-type) and 1.13 (n-type) in BT. This achievement is primarily attributed to the nonequilibrium solidification mechanism, which leads to the formation of multiscale defects during the 3D printing process. The introduction of these multiscale defects enables the effective scattering of wide frequency phonons, leading to a substantial reduction in lattice thermal conductivity. Meanwhile, robust mechanical properties were obtained in the printed p-type/n-type BT TE materials parallel to the building direction (BD) with a compressive strength reaching 257/250 MPa by employing the fine grain structure and the high density of nanotwins introduced during the SLM process. A well shape-controllable and high-performance TEG was designed using 3D-printed BT half-rings, and an output power of 134 mW was achieved at a temperature gradient of 38.9 °C. Our study opens a new route for the great potential of TE materials based on standard commercial SLM 3D printing technology for low-grade waste heat emitted from structures with heterogeneous shapes.

Predictable Thermoelectric Performance of Directly Synthesized Bi0.5Sb1.5Te3 Using Laser Powder Bed Fusion Additive Manufacturing

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

3D-Printing of Shape-Controllable Thermoelectric Devices with Enhanced Output Performance

3D Printing of Bi2Te3-Based Thermoelectric Materials with High Performance and Shape Controllability

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

High Thermoelectric Performance of p-Type Bi0.4Sb1.6Te3+ x Synthesized by Plasma-Assisted Ball Milling

Realizing high thermoelectric performance in Te nanocomposite through Sb2Te3 incorporation

Making High Thermoelectric and Superior Mechanical Performance Nb0.88Hf0.12FeSb Half‐Heusler via Additive Manufacturing

High performance thermoelectric composites via scalable and low-cost ink processing

Synergistic Combination of Sb2Si2Te6 Additives for Enhanced Average ZT and Single-Leg Device Efficiency of Bi0.4Sb1.6Te3-based Composites

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Enhanced thermoelectric and mechanical properties of Bi0.5Sb1.5Te3 alloy with dispersed yttrium oxide ceramic nanoparticles

Synergistic modulation of mobility and thermal conductivity in (Bi,Sb)2Te3 towards high thermoelectric performance

High-performance Ag0.8Pb18+xSbTe20 Thermoelectric Bulk Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering

Development of Nanostructured Bi2Te3 with High Thermoelectric Performance by Scalable Synthesis and Microstructure Manipulations

Fabrication and Property of High-Performance Ag-Pb-Sb-Te System Semiconducting Thermoelectric Materials

Thermoelectric performance of p-type (Bi,Sb)2Te3 incorporating amorphous Sb2S3 nanospheres

Enhanced Thermoelectric Performance of N-Type Bi2Te2.7Se0.3 Via a Simple Liquid-Assisted Shear Exfoliation

Direct ink writing of high-performance Bi2Te3-based thermoelectric materials by quasi-inorganic inks and interface engineering

Enhanced thermoelectric performance of 3D-printed Bi2Te3-based materials via adding Te/Se

Machine Learning-Assisted 3D Printing of Thermoelectric Materials of Ultrahigh Performances at Room Temperature