Abstract:Introduction . To improve the vibrating rollers in order to increase sealing capacity, reliability and vibration safety, the interaction of vibrating roller parts between each other and with compacted soil is simulated mathematically. The developed models are validated, i.e. compared with the results of experimental studies. However, the known results of experimental studies were obtained based on a relatively small list of vibrating roller models and soil types, as well as in a steady vibration mode. The paper presents the results of experimental studies, which used a vibratory drum of a roller to study its vertical vibration accelerations both in the steady vibration, as well as transient mode at turning the vibration generator on (speedup) and off (halt). This expands the range of opportunities to validate the existing and newly developed mathematical models. Materials and methods . Experimental studies of vertical vibration accelerations of a drum were conducted using the DM-617 vibrating roller when compacting natural sand-gravel aggregate. The accelerometer readings show high-frequency harmonics, which makes it significantly more difficult to determine amplitude values of vibration accelerations, therefore a low-frequency filter with a boundary frequency of 200 Hz was used for digital processing. Results . It was determined that when the DM-617 vibrating roller is compacting soil with maximum driving force within the range of variation of dynamic modulus of soil deformation E vd =14...25 MPа, amplitude values of vertical vibration accelerations of the vibratory drum are from 65... 77 to -61... -69 m/s2 . At the start-up (speedup) of vibration generator, acceleration amplitudes are 1.1 times higher than vertical accelerations of steady operation mode of the vibrating drum and practically do not depend on the dynamic modulus of soil deformation E vd . At turning off (stop) of the vibration generator, amplitude of vertical accelerations do not exceed the vertical accelerations of the steady operation mode of the vibratory drum. Discussion and conclusion . The vertical acceleration amplitudes of vibratory drums of DM-617 do not depend on the dynamic soil deformation modulus E vd , and this is consistent with the results of experimental studies of the vibratory drum mounted on DM-614. The obtained vertical vibration accelerations of the drum mounted on DM-617 in the steady vibration mode, as well as at switching the vibration generator on (speedup) and off (halt) make it possible to verify the existing and developed mathematical models of interaction of vibrating rollers with compacted soil. Financial transparency: the authors have no financial interest in the presented materials or methods. There is no conflict of interest.

The Dynamic Performance of a Self Moving Roller

Dynamic response of rigid pavements to moving vehicles

The Dynamic Response of the Vibrating Compactor Roller, Depending on the Viscoelastic Properties of the Soil

Dynamic Model of Off-road Vehicle for Ride Comfort Simulation

Vibration Analysis of High-speed Traction Elevator Based on Guide Roller-rail Contact Model

Dynamic Analysis of Double-Row Self-Aligning Ball Bearings Due to Applied Loads, Internal Clearance, Surface Waviness and Number of Balls

Consideration of the Variable Contact Geometry in Vibratory Roller Compaction

Experimental studies on soil compaction using BOMAG BW 226 BVC-5 vibratory roller

Dynamical response to vibration roller compaction and its application in intelligent compaction

Change of Structure of Dispersion Material Under Dynamic Loads

Nonlinear Dynamics of the Rigid Drum for Vibratory Roller on Elastic Subgrades

Study nonlinear vibration characteristics of vibrating roller-subgrade coupled system in the initial and middle stages of vibratory compaction

Discrete Simulation of Vibratory Roller Compaction of Field Rockfills

A Study on the Analysis of the Ground Compaction Effect According to the Roller Operation Method through CMV Analysis Using IC Rollers

A Dynamic Assessment of Rubber–Sand Mixtures as Subgrade Materials during Vibratory Roller Compaction through DEM Simulation in 2D

Model for dynamic characteristics produced by inner race local defect in ball bearing system and its simulation

Structure and Analysis of an Omni-directional Wheel with Circular Conical Rollers

Dynamic modeling and characteristics analysis of cylindrical roller bearing with the surface texture on raceways

Effects of the Dynamic Wheel–rail Interaction on the Ground Vibration Generated by a Moving Train

Nonlinear Vibration Characteristic Analysis of Roller-Plate System Based on Asymptotic Methods

RESULTS OF EXPERIMENTAL STUDIES OF ACCELERATIONS OF THE DM-617 VIBRATORY ROLLER USING DIGITAL SIGNAL PROCESSING TECHNOLOGY