Abstract:Formulation of the problem. The process of densification of mixtures of construction products that are being formed or molded is an important stage in the formation of a macrostructure, since during this period, granular and other components of the composite that fill it are relatively firmly fixed in a viscous medium. A large number of publications are devoted to the study of this issue, but many aspects of the effect of compaction on the structure of a conglomerate are not yet known, and the results obtained have not been systematized. Introduction. Preliminary compaction of the mixture reduces the fragmentation of particles, transferring bonds from point to interfacial along the contact boundaries. With the approach of particles to very small distances, repulsive forces arise and increase. Ultimately, the resultant force acts, which, at a certain optimal distance of particles from one another, provides the initial cohesion of the raw product. Fixation occurs both directly by adjoining the components, including with the possibility of intergrowth (for example, crystals), and through interlayers of a completely hardened or gradually hardening binder. In conglomerate materials, contact through interlayers at the compaction stage is more typical than direct contact or coalescence of particles under the influence of surface energy, chemical bonds, or other, including complex, factors. Objective. The aim of the work was to establish the features in the formation of the structure of the conglomerate from the preliminary compaction of the mixture, as well as its influence on the functional and technological characteristics. Methods. Solving the problem of the optimal structure of a conglomerate requires identifying the relationship between the type, concentration, composition of raw materials, the method of compaction and the resulting functional characteristics of the product. Results. Optimization of the structure while maintaining the level of desired properties corresponds to achieving the highest quality in a material or product. Technology by this criterion becomes progressive. To reduce the water penetration of cement concretes, it is necessary to provide optimal conditions for cement hydration and the creation of a dense conglomerate with a minimum number of pores. In connection with the relevance of creating building materials and products from materials of the construction environment (soil blocks) and reducing energy consumption during molding and pressing, it is necessary to continue the development of technologies and equipment designs to obtain the optimal conglomerate structure with minimal water penetration. Conclusion. Studies of the effect of compaction of raw materials on the structure of conglomerates are ongoing, but already these results indicate that the rate and form of conglomerate formation change significantly at optimal values of pre-compacted raw materials.

Change of Structure of Dispersion Material Under Dynamic Loads

Compaction Pressure Distribution and Pressure Uniformity of Segmented Rollers for Automated Fiber Placement

Mechanical Evaluation of Aggregate Gradation to Characterize Load Carrying Capacity and Rutting Resistance of Asphalt Mixtures

Energy-Based Kinetics Approach for Coupled Viscoplasticity and Viscofracture of Asphalt Mixtures

A new approach to laboratory roller compaction method and its influence on surface texture and permanent deformation of asphalt mixtures

Evaluation of heavy roller compaction on a large-thickness layer of subgrade with full-scale field experiments

A Study on the Analysis of the Ground Compaction Effect According to the Roller Operation Method through CMV Analysis Using IC Rollers

Interlocking Evaluation of Mesoscopic Skeleton with the Compaction Degree of Hot-Mix Asphalt

Influence of Compaction Methods on the Optimum Moisture Content and Performance of Roller Compacted Concrete Pavements

The Dynamic Response of the Vibrating Compactor Roller, Depending on the Viscoelastic Properties of the Soil

Investigation of Particle Rotation Characteristics and Compaction Quality Control of Asphalt Pavement Using the Discrete Element Method

A Dynamic Assessment of Rubber–Sand Mixtures as Subgrade Materials during Vibratory Roller Compaction through DEM Simulation in 2D

Experimental and Numerical Analysis on Mesoscale Mechanical Behavior of Coarse Aggregates in the Asphalt Mixture during Gyratory Compaction

Pressure Distribution for Automated Fiber Placement and Design Optimization of Compaction Rollers

Experimental Study on Vibratory Compaction Behavior of Tunneling Rock Wastes Used as Unbound Permeable Aggregate Base Materials

Influence of Different Compacting Methods on Mix Design of Semi-rigid Base Materials

Soil Structure Effects on Deformation, Pore Water Pressure, and Consequences for Air Permeability During Compaction and Subsequent Shearing

Dynamic response of asphalt pavement under vibration rolling load: Theory and calibration

Mesoscopic Mechanical Properties of Aggregate Structure in Asphalt Mixtures and Gradation Optimization

EFFECT OFTHE COMPACTION PROCESS ON THE CONGLOMERATE STRUCTURE AT PRODUCTION OF CONSTRUCTION MATERIALS

Experimental studies on soil compaction using BOMAG BW 226 BVC-5 vibratory roller