Abstract:Oxidative etching possesses an enriched flexibility and atomic-level accuracy in tailoring the size, morphology, surface structure, and composition of colloidal nanocrystals toward their catalytic and sensing applications. In this work, we choose one-dimensional penta-twinned Pd nanorods as a model system and apply liquid cell transmission electron microscopy (LCTEM) to investigate the detailed nanoscale etching process under different solution environments, which are DI water/e-beam (weakly oxidative), sodium chloride (NaCl) solution/e-beam (moderately oxidative), and ferric chloride (FeCl3) solution/e-beam (strongly oxidative), respectively. Increasing the oxidative strength of solution alone accelerates the dissolution kinetics and drives the system from the (near)-equilibrium etching, where nanorods appear in flat and low-indexed ends (for DI water/e-beam) to nonequilibrium etching with slender tips formed as intermediate products (for FeCl3/e-beam). Under a nonequilibrium etching condition, both symmetric and asymmetric etching occurred, that is, the penta-twinned structure either retained (for symmetric etching) or dissolved to a fourfold-, threefold-, and twofold-twinned and single-crystalline structure (for asymmetric etching), depending on the structural defects-induced strain distribution. The formation of slender tips of different structures can be further understood via energetic analysis and strain relaxation. In particular, in situ LCTEM results were successfully reproduced by flask system-based etching experiments; hence, direct correlations were built between LCTEM and conventional colloidal etching reactions. This work comprehends the present understanding on the synergetic roles of structure characteristics and solution chemistry for the etching of multiply twinned nanoparticles toward their precise controlled synthesis and practical applications.

THREE-DIMENSIONAL MODEL OF ETCHING FIGURE OF ANDALUSITE AND ITS RELATION WITH CRYSTAL SYMMETRY

Synergy Between Structure Characteristics and the Solution Chemistry in a Near/Non-Equilibrium Oxidative Etching of Penta-Twinned Palladium Nanorods

New Application of the Traditional Method: Crystal Etching

ETCHING FIGURE OF Α-Quart TWINNING ON DIFFERENT CRYSTALLOGRAPHIC FACES AND CRYSTAL SYMMETRY

Dislocation Etching Morphology on the A Plane of Sapphire Crystal

Tridimensional morphology and kinetics of etch pit on the {0 0 0 1} plane of sapphire crystal

Etching Rate Analysis Model Based on Quartz Bond Angle Characteristics

Three-dimensional modeling of pitting corrosion considering the crystallographic orientation of the microstructure

Effect of crystal orientations and precipitates on the corrosion behavior of the Al-Cu alloy using single crystals

Cavity Etching Evolution on the A-plane of Sapphire Crystal in Molten KOH Etchant

Unraveling Anisotropic and Pulsating Etching of ZnO Nanorods in Hydrochloric Acid via Correlative Electron Microscopy

Experiment Study on Micro-Structure on Different Crystallographic Planes of Mc-Si Etched in Alkaline Solution

Morphology and Etch Figures of A Yb:Yal3(Bo3)(4) Crystal

AFM and SEM Study on Crystallographic and Topographical Evolution of Wet-Etched Patterned Sapphire Substrates (PSS) I. Cone-Shaped PSS Etched in Sulfuric Acid and Phosphoric Acid Mixture (3:1) at 230°C

Crystal Structure of Aluminum Sulfate Hexadecahydrate and Its Morphology

Mechanism of Etching of Al-4.5Mg-1.0Mn Alloy

The Model of Etching of (hkl) Planes in Monocrystalline Silicon

Crystallography of precipitates in Mg alloys

Dissolution and early hydration of tricalcium aluminate in aqueous sulfate solutions

Anisotropic etching of Si

Visualizing the Internal Nano‐crystallinity of Calcite due to Non‐classical Crystallization by 3D Coherent X‐ray Diffraction Imaging