Design on Soft-starting and Protection Controller for Asynchronous Motor Based on Microprocessor AT89C52

Wei Yang

2003-01-01

Abstract:Aimed at bad start up performance of asynchronous motor,the soft start up and protection controller is developed based on microprocessor AT89C52.The mechanism of controller,software and hardware are introduced.The practice proved that the controller has good performance.

What problem does this paper attempt to address?

Design of Soft Start Energy-Saving Controller of Asynchronous Motor

刁红泉,颜钢锋

DOI: https://doi.org/10.3785/j.issn.1006-754x.2004.03.010

2004-01-01

Journal of Engineering Design

Abstract:Asynchronous motor has an extensive application in manufacture. The efficiency is quite low when the motor is running under the rated load. Dynamically adjusting the terminal voltage of the motor according to the change of the load can greatly reduce the consumption, and thus improve the efficiency. This paper provides design of the soft start energy-saving controller of motor, which can be used in energy-saving, soft start and running protection. The controller needs a low cost in hardware, but the function is powerful. This paper proposes the software and hardware design scheme of the controller.
Research on System of Self-Controlled Soft Start with Variable Frequency for Synchronous Motor

Jin Guangzhe,Zhou Changcheng,Gao Qiang,Xu Dianguo

DOI: https://doi.org/10.1109/ipemc.2012.6259259

2012-01-01

Abstract:High-power synchronous motor is difficult to start and unable to start and stop freely, so it must be long-running. This will cause a lot of energy waste. In order to solve the problem, devices of self-controlled soft start with variable frequency for high-power synchronous motor are researched and developed. The TMS320F2812 DSP is used as main control chip to do all the control strategies in this soft-start platform. This paper also gives a detailed method to do with the error signal of misleading zero-crossing points of back-EMF caused by inverter commutation, and describes the problem at the switch point from self impulse to back-EMF zero-crossing detection. It can get the rotor position without position sensor by accurate detection of motor back-EMF zero-crossing at medium and high speed. In the prototype platform, the motor can be soft started from standstill to rated speed stably and reliably.
Study of Soft Starting Controller with High Performance and Low Cost

胡长生,韩珏,苏行,张仲超

DOI: https://doi.org/10.3969/j.issn.1000-100x.2004.05.018

2004-01-01

Abstract:The paper researches on the torque control starting method and introduces a kind of soft starting controller with high performance and low cost based on Intel 8XC196MC , which can solve the imbalance of three phase in electric network. The torque control starting method was applied in the controller. The prototype was developed. The datum of ex-periments show the torque control starting method can work effectively?
Design Of Comprehensive Motor Protector Based On Improved Sliding-Window Iterative Dft Algorithm

Jinxiang Zhan,Xiaoxiao Cheng,Qunwei Xu,Liang Wu,Guozhu Chen

DOI: https://doi.org/10.1109/ipemc.2016.7512881

2016-01-01

Abstract:This paper introduces a design of comprehensive motor protector based on improved sliding-window iterative discrete fourier transform (DFT) algorithm. It improves the conventional sliding-window iterative DFT, making it easier in calculation and reducing the computation burden of the microprocessor. With electric parameters updating every sampling period, the time response to faults is much improved, compared to the conventional motor protector. For the hardware plan, the protector is controlled by two microcontrollers, one is for the control and measurement module and the other is for the display module. They are connected through RS422 communication. The whole device is compact and layout reasonable, with the advantages of small size and high reliability. The motor protector designed in this paper integrates protection, control, measurement, and communication. Experiment results have verified that it has good performance and high accuracy and can provide comprehensive protection for the motor.
The Comprehensive Control Device of Alternating Current Motor

LONG San-ping,LIU Wei,LUO Yao-hua

DOI: https://doi.org/10.3969/j.issn.1009-671x.2005.02.011

2005-01-01

Abstract:The comprehensive control scheme for the starting and running of asynchronous motor is presented. The asynchronous motor soft_starter controlled by single_chip microcomputer is used as a controller, and double_action thyristor as voltage adjusting element. It includes soft_starting, saving_energy and protective techniques. When the load of an asynchronous motor is less than rating or nothing, it varies the value amplitude of Stator_winding voltage, reducing the loss, and enhancing the efficiency. The soft_starter and energy_saving for an asynchronous motor are analyzed. The efficiency is verified by simulation.
Frequence Control System of AC Asynchronous Motor Based on AT89S52

Dong Jiaxi,Chang Jiaxing,Wang Xiaoming

2013-01-01

Abstract:The AC asynchronous motor has features of simple structure,cheap price and convenient maintenance.It is widely used in the production.This article takes AT89S52 as the control core,uses SA4828 for speed control chip and PS21564 intelligent power module for integrated drive circuits.They controls a three-phase asynchronous motor.
STUDY ON SOLID STATE ENERGY SAVING STARTER WITH FUZZY CONTROLLER FOR ASYNCHRONOUS MOTORS

Xiaoyun SUN,Donghui LIU,Jianni SHENG

DOI: https://doi.org/10.3969/j.issn.1003-3076.1999.03.015

1999-01-01

Abstract:This paper introduced a principle and a design of soft ware and hardware on the solid state energy saving starter for asynchronous motors,which uses a single chip microcomputer to control pulse triggering,soft starting,energy saving,and false detecting.This control algorithm improves the precision of the system.It has the wide prospect on energy saving.
Soft-starter of Asynchronous Motor Based on Power Factor Closed-loop Control

SUN Li-wei,SUN Li

DOI: https://doi.org/10.3969/j.issn.1001-6848.2008.03.001

2008-01-01

Abstract:The large starting current of asynchronous motor may bring about great impact to electric network.According to the analysis of power factor characteristic in asynchronous motors,this paper brings forward a closed-loop control method using the power factor angle as the feedback variable of the system,avoiding the vibration of electromagnetic torsion and currents by variation of input-voltage during the starting process of motors.The above strategy ensures the voltage regulation according to the expected rules.The experiment results prove the availability of the method.
Research of Electronic Soft Starter Based on Intel196MC

苏行,胡长生,张仲超

DOI: https://doi.org/10.3969/j.issn.1001-4551.2004.06.001

2004-01-01

Abstract:Here presents a kind of electronic soft starting controller based on Intel196MC. The control function of the soft starter can be more accuracy through use of this MCU. The paper gives the main working principle and the main circuit of the soft starter, analyzed the production of the triggering signal and the design of the software. Then experimental results obtained from a prototype confirm the validity and feasibility of the proposed method.
Research and Simulation of SCR Soft-Start Asynchronous Motor

Quan Li,Xin Wang,Jun Zhou

DOI: https://doi.org/10.2991/icaees-15.2015.212

2015-01-01

Abstract:Direct starting method of asynchronous motor does a lot harm such as current surge and mechanical shock, etc . In order to reduce the harmful influence of direct starting method and improve the starting performance of asynchronous motor, a scheme of asynchronous motor soft starting system based on antiparallel SCR is designed in this paper. Firstly, it analyzes the starting performance of asynchronous motor. Secondly, based on the performance results above, the scheme of three-phase asynchronous motor soft starting system is established. It regulates stator voltage of the motor by SCR regulating system, transformers the synchronous phase voltage to wide pulse wave by trigger module and obtains thyristor gate signal by integrator, so as to achieve the soft-start of asynchronous motor. Finally, by comparing and analyzing the simulation results of direct starting system and soft starting system, it shows that the feasibility and advantages of the SCR type's asynchronous motor soft starting system.
Study of an Intelligent Low-Voltage Integrative Motor Protector Based on PIC16G876 Single Chip

Wei-ming TONG,Zhong-wei LI,Wen-li NI

DOI: https://doi.org/10.3969/j.issn.1674-3415.2005.03.011

2005-01-01

Abstract:To resolve the contradiction between the function and the cost of the motor protectors in the market, a high performance-cost ratio and intelligent low-voltage integrative motor protector based on PIC16F876 single chip of microchip incorporation is designed. The inverse time characteristic of overload protection and the differences of starting protection and running protection are described in detail. A special algorithm is put forward to calculate in program, it solves the problem about low precision of fixed-point operation and high computation cost and long computation time of floating-point operation. To improve the reliability and the anti-interference ability of the equipment, many anti-interference measures are taken in designing the hardware and software. The results of dynamic simulation and test in the field indicate that this motor protector could make precise judgement to every kind of faults of the low-voltage motor protector and have higher reliability and repetition. The precisions of its action value and action time can meet the need of general egineering application. This project is supported by Heilongjiang Technologies RD Programme(No.GB02A103).
The study and application of Liguid resistance soft starting motor

Zhang Lun

2007-01-01

Abstract:This paper explains mechanial characteristic of motor.The motor soft-strat implication;Adopt new technigues PLC control soft-strar hardware structvre and working principle;the paper introdrces PLC soft-strat programming,debugging,fix a breakdown and main protect functions.aswell as introduces go to factory debugging and runing case.
Research on microcomputer protective device for asynchronous motor

LIU Yu-min,TIAN Ku,LI Shao-yuan

DOI: https://doi.org/10.3969/j.issn.2095-0926.2007.03.011

2007-01-01

Abstract:Based on symmetrical analysis theory,the stator current of motor is decompounded into positive-sequence current,negative sequence current and zero-sequence current to distinguish the running state and fault type of the motor according to their magnitude of current.The technology of INTEL80C196KB MCU is applied to design and fulfill a new kind of micro-processor protective device for asynchronous motor.The device has perfect protective functions,unfailing performance,steady operation and easy attendance.The criterion of protection,the hardware structure and the protection algorithm are introduced.
Soft Start Control of Large-Capacity Synchronous Motor

SUN Xudong

DOI: https://doi.org/10.3321/j.issn:1000-0054.1999.09.006

1999-01-01

Abstract:Soft start with thyristor ac dc ac converter is a dominant starting method of large capacity synchronous motors at present. Constant lead angle control is replaced by constant margin angle control to reduce start current and start time. Some key problems in constant margin angle digital control system were analyzed such as stability, rotor position signal forming and control of inverter and excitation, also their solutions were presented. Motor parameters obtained with on line identification were used to calculate the lead angle, thus its accuracy was raised. A digital control system of a 7.8MW synchronous motor soft start was set up. Both analysis and operation show that the constant margin anlge control is an effective way to lower start current and shorten start time.
Technology of Asynchronous Motor Soft Starter and Simulation Research for Torque Control Strategy

童玲,王志新,张华强,刘启中,陈道贤

DOI: https://doi.org/10.3969/j.issn.1001-2095.2010.04.011

2010-01-01

Abstract:Soft starter technology is advantageous to the improvement and the control of the startup proce-dure of asynchronous motor. The features of each kind of soft-start method were analyzed and compared in de-tail. Solid soft starter was realized on the bases of thyristor series technology and the torque control strategy. Through a 3 kW motor's simulation,the soft starter with torque control technology can greatly reduce the dy-namic torque and starting current. The performance is able to good control the startup procedure of asyn-chronous motor.
The Design of the Controller for Vehicle Brush-less DC Motor Based on LIN Bus

Qin Guoping,Yao Wei,Zhang Wei

DOI: https://doi.org/10.3321/j.issn:1000-680X.2006.06.018

2006-01-01

Abstract:The controller for a brush-less DC motor based on LIN bus is developed with the overall structure and the implementation of hardware and software described in detail.The test results show that the controller is stable,reliable,meeting the design requirements.
Intelligent Protector for Motor Based on PICmcu

ZHAO Rong-xiang,Qian Hao,CHEN Tong

DOI: https://doi.org/10.3785/j.issn.1006-754x.2005.02.006

2005-01-01

Journal of Engineering Design

Abstract:This paper introduced an intelligent protector for motor based on PICmcu, and presented the design thought of its hardware circuit and software. The section concerning hardware circuit focused on the design of the circuits of separate section and while the section about software illuminated the design method of key parts with details. An intelligent communication system utilized between intelligent protector and PC is also involved. Practical application indicated that this protector can achieve satisfactory protection on motor.
A novel power quality improved AC voltage controller for soft starting of squirrel cage induction motors

Mohamed Faizal,G. Kannayeram,Agnes Prema Mary,Faizal, Mohamed

DOI: https://doi.org/10.1007/s43236-024-00784-7

IF: 0.913

2024-03-20

Journal of Power Electronics

Abstract:Soft starting of a squirrel cage induction motor (SCIM) is a general requirement in industries. Until now, the soft starting systems of squirrel cage induction motors have been using phase angle controllers implemented using thyristors. The major disadvantage of thyristors-based control is that the source current becomes polluted with harmonics. In addition, while phase angle-controlled soft starting schemes are suitable for star connected motors, they introduce high torque ripple resulting in noise and turbulence. To overcome this issue, a novel soft starting topology is proposed for the squirrel cage induction motors that guarantees improved power quality on both the source side and the load side. The proposed system uses a three-phase power electronic chopper with a freewheeling arrangement. Throughout the starting process, the source side current is sinusoidal and the source side power factor is unity. The proposed method has been found to be useful for both Star and Delta connected squirrel cage induction motors. The proposed system has been validated using simulations in the MATLAB/Simulink environment and on an experimental prototype.

engineering, electrical & electronic
Application of Soft-Start in Electromotor Starting

卢宇,涂光瑜,罗毅,盛戈皥,朱仲彦

DOI: https://doi.org/10.3969/j.issn.1674-3415.2003.05.006

2003-01-01

Abstract:The paper presents a new switch with soft starting,which consists of a group of anti parallelly connected thyristors and common switch,and can open or close without arc.This system mainly contains a single chip,a signal converter,a synchronous circuit and a pulse magnifier circuit.The functions of the system software include electricity detection,error recognition and protection,alarming,etc.The system has the ability to set the start up voltage,start up current and start up time.The device can solve the problem of over current in electromotor start up process,and has the digital displaying of fault such as under voltage,over voltage and over current,etc.
ARM-based Control of AC Asynchronous Motors and Design of an Energy Feedback System

Bin-bin ZHANG,Guo-hua SHU,Jun-wu DING

DOI: https://doi.org/10.3969/j.issn.1000-3886.2015.05.001

2015-01-01

Abstract:Based on ARMkernel microcontroller and IPM(Intelligent Power Module)and by use of SVPWM(Space voltage Vector Pulse Width Modulation)and vector control method,this paper introduces a variable frequency speed control system for the three-phase asynchronous motor.In view of energy loss of regenerative brake occurring during quick startup and brake of the general-purpose inverter and frequent normal and reverse speed control,we add a grid device for inversion feedback of the regenerative braking energy.Detailed software and hardware design is shown and implemented.The experiment result shows that the system has a high control precision and good real-time performance.It also allows that the inverter can operate in four quadrants,producing remarkable energy-saving effect.

Design on Soft-starting and Protection Controller for Asynchronous Motor Based on Microprocessor AT89C52

Design of Soft Start Energy-Saving Controller of Asynchronous Motor

Research on System of Self-Controlled Soft Start with Variable Frequency for Synchronous Motor

Study of Soft Starting Controller with High Performance and Low Cost

Design Of Comprehensive Motor Protector Based On Improved Sliding-Window Iterative Dft Algorithm

The Comprehensive Control Device of Alternating Current Motor

Frequence Control System of AC Asynchronous Motor Based on AT89S52

STUDY ON SOLID STATE ENERGY SAVING STARTER WITH FUZZY CONTROLLER FOR ASYNCHRONOUS MOTORS

Soft-starter of Asynchronous Motor Based on Power Factor Closed-loop Control

Research of Electronic Soft Starter Based on Intel196MC

Research and Simulation of SCR Soft-Start Asynchronous Motor

Study of an Intelligent Low-Voltage Integrative Motor Protector Based on PIC16G876 Single Chip

The study and application of Liguid resistance soft starting motor

Research on microcomputer protective device for asynchronous motor

Soft Start Control of Large-Capacity Synchronous Motor

Technology of Asynchronous Motor Soft Starter and Simulation Research for Torque Control Strategy

The Design of the Controller for Vehicle Brush-less DC Motor Based on LIN Bus

Intelligent Protector for Motor Based on PICmcu

A novel power quality improved AC voltage controller for soft starting of squirrel cage induction motors

Application of Soft-Start in Electromotor Starting

ARM-based Control of AC Asynchronous Motors and Design of an Energy Feedback System