Abstract:Engineered Cementitious Composite (ECC) exhibits superior tensile ductility, shear capacity, and crack-control ability in comparison to traditional concrete and fiber reinforced concrete. These attributes render ECC a suitable candidate for addressing the brittle punching shear behavior commonly observed in reinforced concrete (RC) flat slabs. To verify the feasibility of using ECC for strengthening the punching shear capacity of concrete slabs, an investigation on the punching behavior of plain ECC slabs was conducted to ascertain their crack patterns, failure mode, strength and energy absorption capacity by means of experiments on twenty-seven 400 mmx400 mm square slabs. The plain ECC slabs were simply supported on a bespoke steel framework with eight supports, centrically loaded with a concentrated load. The fiber volume fraction (FVF) and span-depth ratio (SDR) are the two variables to be examined for their effects on the punching behavior of ECC slabs. Test results revealed that the incorporation of fibers significantly improved the load-bearing capacity, ductility and energy absorption capacity, while it altered the failure mechanism from brittle to ductile. The critical punching shear angles of all tested plain ECC slabs ranged from 40 degrees to 50 degrees. The ECC specimens possessing an FVF of 2 % exhibited markedly superior tensile capabilities compared to those with a 1 % FVF, as evidenced by direct tensile tests. Nevertheless, the ECC slabs with an FVF of 2 % did not demonstrate commensurate improvements in loadbearing capacity relative to their counterparts containing 1 % FVF. The span-depth ratio significantly impacted the failure mode of plain ECC slabs, yielding to punching shear failure at an SDR of 1, and to flexural failure at SDRs of 2 and 3. Moreover, an increase in the SDR value led to a reduction in both the initial cracking load and the ultimate load, concurrently increasing the associated deflection. In addition, a preliminary theoretical analysis was conducted to estimate the bearing capacity of plain ECC slabs. Flexural strength was estimated by yield line theory (YLT) and punching shear resistance was estimated by the model based on theory of plasticity in slab-column systems. The experimental and theoretical investigations could provide insights into the punching and flexural behavior of ECC slabs, laying a groundwork for the design and development of flat systems strengthened with ECC.

Flexural Behaviors of 3D Printed Lightweight Engineered Cementitious Composites (ECC) Slab with Hollow Sections

Experimental and numerical study on the flexural behavior of 3D-printed composite beams with U-shaped ECC formwork

Flexural performance of 3D-printed composite beams with ECC and recycled fine aggregate concrete: Experimental and numerical analysis

Mechanical properties of engineered cementitious composites beams fabricated by extrusion-based 3D printing

3D-Printed LC3-based Lightweight Engineered Cementitious Composites: Fresh State, Harden Material Properties and Beam Performance

Mechanical behaviors of 3D printed lightweight concrete structure with hollow section

3D-Printable Engineered Cementitious Composites (3DP-ECC): Fresh and Hardened Properties

Mechanical Properties of 3D Printed ECC Beams Reinforced with FRP Mesh

Development of 3D Printable Engineered Cementitious Composites with Ultra-High Tensile Ductility for Digital Construction

Experimental Investigation of Flexural and Punching Behavior for Plain PE-ECC Slabs with Different Fiber Volume Fractions and Span-Depth Ratios

Crack propagation and failure mechanism of 3D printing engineered cementitious composites (3DP-ECC) under bending loads

Anisotropic Size Effect of 3D Printed LC3-based Engineered Cementitious Composites (LC3-ECC)

Effect of Reinforcement Configurations on the Flexural Behaviors of 3D Printed Fiber Reinforced Cementitious Composite (FRCC) Beams

A Numerical Study on 3D Printed Cementitious Composites Mixes Subjected to Axial Compression

Flexural behavior of precast ultra-lightweight ECC-concrete composite slab with lattice girders

Low-carbon, expansive engineered cementitious composites (ECC) in the context of 3D printing

Flexural Performance of Layered ECC-concrete Composite Beam

Flexural performance of novel ECC-RC composite sandwich panels

On the Emergence of 3D Printable Engineered, Strain Hardening Cementitious Composites (ECC/SHCC)

Use of high strength, high ductility engineered cementitious composites (ECC) to enhance the flexural performance of reinforced concrete beams

Effects of Anisotropic Mechanical Behavior on Nominal Moment Capability of 3D Printed Concrete Beam with Reinforcement