Abstract:Concrete 3D printing, an innovative construction technology, offers reduced material waste, increased construction speed, and the ability to create complex and customized shapes that are challenging to achieve with traditional methods. This study delves into the unique fresh-state performance required for 3D printing concrete, discussing buildability, extrudability, and shape retention in terms of concrete rheology, which can be modified using admixtures. Currently most 3D printing concretes feature high cement contents, with little use of secondary cementitious materials. This leads to high embodied carbon, and addressing this is a fundamental objective of this work. The research identifies attapulgite, bentonite, and sepiolite clay as potential concrete admixtures to tailor concrete rheology. Eight low-carbon concrete mixes are designed to incorporate GGBS at a 50% replacement level and are used to measure the influence of each clay on the concrete rheology at varying dosages. A comprehensive rheological test protocol is designed and carried out on all mixes, together with other tests including slump-flow and compression strength. The objective is to determine the applicability of each clay in improving the printability of low-carbon concrete. The findings reveal that at a dosage of 0.5%, sepiolite was seen to improve static yield stress, dynamic yield stress, and rate of re-flocculation, resulting in improved printability. The addition of attapulgite and sepiolite at a dosage of 0.5% by mass of binder increased compressive strength significantly; bentonite had very little influence. These gains are not repeated at 1% clay content, indicating that there may be an optimum clay content. The results are considered encouraging and show the potential of these clays to enhance the performance of low-carbon concrete in 3D printing applications.

Low-carbon, expansive engineered cementitious composites (ECC) in the context of 3D printing

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

Time-dependent fresh properties characterization of 3D printing engineered cementitious composites (3DP-ECC): On the evaluation of buildability

Printability region for 3D-printable engineered cementitious composites (3DP-ECC)

A rheological-based printability assessment method for 3D printing Engineered Cementitious Composites considering fiber dispersion

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation

Engineered cementitious composites using blended limestone calcined clay and fly ash: Mechanical properties and drying shrinkage modeling

Mechanics, hydration phase and pore development of embodied energy and carbon composites based on ultrahigh-volume low-carbon cement with limestone calcined clay

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

Eco-Friendly, Set-on-Demand Digital Concrete

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

Multiscale Investigation on the Performance of Engineered Cementitious Composites Incorporating PE Fiber and Limstone Calcined Clay Cement (LC3)

Development of Sustainable Engineered Cementitious Composites by Incorporating Local Recycled Fine Aggregate

Effect of supplementary cementitious materials on properties of 3D printed conventional and alkali-activated concrete: A review

Ultra-low carbon lightweight engineered cementitious composite: Design and material characterization

Shear behaviors of engineered cementitious composites to seawater sea-sand concrete (ECC-to-SSSC) interfaces cast using 3D-printed pre-grooving formwork: Mechanical properties, characterization, and life-cycle assessment

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Relationship between microstructure and strain-hardening behaviour of 3D printed engineered cementitious composites

Incorporating coarse aggregates into 3D concrete printing from mixture design and process control to structural behaviours and practical applications: a review

The Role of Different Clay Types in Achieving Low-Carbon 3D Printed Concretes

3D-printing of architected calcium silicate binders with enhanced and in-situ carbonation