Abstract:As we know, 3DPC is printed layer by layer compared with mold-casting conventional concrete. Pore structure and layer-to-layer interface are two main aspects of the internal structure for 3DPC, which decide 3DPC's mechanical performance. The layer-to-layer interface caused by printing is specific to 3DPC. The emphasis of this study lies in the layer-to-layer interfaces of 3DPC. The first aim of this study is to quantify the characteristics of the layer-to-layer interface and therefore characterize different aspects of the interfaces. The second aim of this study is to explore how the internal structure of printed concrete influences the mechanical performance of 3DPC. This research set out to design a series of experimental comparisons between 3DPC and casted concrete with the same compositions. Mechanical tests, i.e., compressive stress, ultrasonic Pulse Velocity test, flexural tension, and tension splitting, as well as the Ultrasonic Pulse Velocity test, were performed to check the mechanical performance of 3DPC. Contrary to what has often been expected, the mechanical test results showed the printed concrete has a quality not worse than casted concrete with the same recipe. Meanwhile, the X-ray computed tomography (X-CT) is used to characterize the internal structure, pore shapes, and interfaces of 3DPC. First, the investigation revealed that the lower total porosity and fewer big voids could be the fundamental causes meaning 3DPC has a better mechanical performance than casted concrete. Second, the statistics based on aspect ratio show that the distribution curves follow similar trends, regardless of the printed or casted concrete. Third, this study quantified the depth of the different interfaces for 3DPC. The results suggest that the porosity in an interface varies in a range. The author's pioneer work has contributed to our present understanding of the interfaces of 3DPC.

Relationship between microstructure and strain-hardening behaviour of 3D printed engineered cementitious composites

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

Bond shear performances and constitutive model of interfaces between vertical and horizontal filaments of 3D printed concrete

Compressive Behavior of Engineered Cementitious Composites under High Strain-Rate Loading

Time-dependent fresh properties characterization of 3D printing engineered cementitious composites (3DP-ECC): On the evaluation of buildability

Tensile performance of 3D-printed Strain-Hardening Cementitious Composites (SHCC) considering material parameters, nozzle size and printing pattern

Crack propagation and failure mechanism of 3D printing engineered cementitious composites (3DP-ECC) under bending loads

A Multiscale Model for Quantifying Fiber Orientation Effects on the Tensile Properties of 3d Printed Engineered Cementitious Composites (3dp-Ecc)

Mechanical Properties of Structures 3D Printed with Cementitious Powders

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

PVA Fibre Reinforced High-Strength Cementitious Composite for 3D Printing: Mechanical Properties and Durability

Stress–Strain Properties and Gas Permeability Evolution of Hybrid Fiber Engineered Cementitious Composites in the Process of Compression

Mechanical and macrostructural properties of 3D printed concrete dosed with steel fibers under different loading direction

Comprehensive investigations on the relationship between the 3D concrete printing failure criterion and properties of fresh-state cementitious materials

Triaxial compressive behavior of 3D printed PE fiber-reinforced ultra-high performance concrete

Experimental Characterization of Anisotropic Mechanical Behaviour and Failure Mechanisms of Hardened Printed Concrete

Influence of pore defects on the hardened properties of 3D printed concrete with coarse aggregate

Experimental and numerical study on the flexural behavior of 3D-printed composite beams with U-shaped ECC formwork

Optimisation of the Mechanical Properties and Mix Proportion of Multiscale-Fibre-Reinforced Engineered Cementitious Composites

Multiscale Investigation on the Performance of Engineered Cementitious Composites Incorporating PE Fiber and Limstone Calcined Clay Cement (LC3)

A rheological-based printability assessment method for 3D printing Engineered Cementitious Composites considering fiber dispersion