Abstract:An in-situ measurement system for porous alumina (PA) film based on atomic force microscope (AFM) in liquid and reflectometric interference spectroscopy (RIFS) was developed. The present article briefly discusses the principle and structure of the system, and introduces its unique characteristic. The system consists of probe unit, XY scanner, Z-piezo feedback system, computer and software, fiber optic spectrometer, anodization control circuitry etc. When a white light beam illuminates the surface of the film, the reflective light beams at the front and back side of the layer are coherent, and lead to periodical amplifications and extinction in the reflective spectrum with the information of the optical thickness of the film. A fiber optic spectrometer was applied in the system which input the refractive spectrum into the computer by which the optical thickness of the film was calculated. Meanwhile according to the surface topography of PA films by AFM in liquid, the effective refractive index was calculated based on Maxwell-Garnett theory and coherent potential approximation (CPA). So the thickness of PA films could be gained at last. To checkout the feasibility and stability of the system, the real-time scanning and thickness measurement experiments were done during anodization of Al sheets in oxalic acid aqueous solution. In the experiment, the authors used 25 mm diameter aluminum (Al) sheets with 99.999% purity and 0.4 mm thickness as the anode, and graphite rod as the cathode. The pretreatment-cleaned Al sheets were anodized in an aqueous solution of 0.5 mol x L(-1) oxalic acid at the constant temperature (20 +/- 0.2) degrees C with 20 mA x cm(-2) anodization electronic current density. Real-time AFM images of PA film were successfully obtained during anodization. The pore-ratios of Al sheet were 7.81% and 13.83% at oxidizing time 150 min and 180 min respectively. Correspondingly, the effective indexes were calculated to be 1.62 and 1.60, respectively. Combining the reflective spectrum gained by the fiber optic spectrometer, the wave number differences between the two adjacent extrema were 57.69 mm(-1) and 50.00 mm(-1). Based on reflectometric interference spectroscopy, the thickness of PA films was found to be 5.35 and 6.25 microm with oxidizing time 150 min and 180 min respectively. The system has characteristics of convenient manipulation, non-destructive and high-resolution in-situ measurement. And the surface morphology, pore-ratio and effective refractive index can also be gained at the same time.

Microfabrication and Characterization of Parylene AF<inf>4</inf>

Microfabrication And Characterization Of Parylene Af(4)

Copolymerization of Parylene C and Parylene F to Enhance Adhesion and Thermal Stability Without Coating Performance Degradation.

Advanced Conformal Parylene Fabrication for Micro/nano Devices

Improving the Hydrophilicity of Poly(vinylidene Fluoride) Porous Membranes by Electron Beam Initiated Surface Grafting of AA/SSS Binary Monomers

Preparation and characterization of super hydrophobic aerogel coated ultra-high molecular weight polyethylene fabric

Fabrication and Characterization of the Functional Parylene-C Film with Micro/nano Hierarchical Structures

Wettability and surface energy of parylene F

An Annealing Process For Mechanical Strength Improvement Of Parylene Micropore-Arrayed Membrane

Hot Embossing to Fabricate Parylene-Based Microstructures and Its Impact on the Material Properties

An antiadhesion and antibacterial platform based on parylene F coatings

Fabrication and electroadhesion properties of parylene-coated carbon fiber arrays

Parylene C autofluorescence for on-chip highest processing temperature sensing

Highly Controllable and Reliable Ultra-Thin Parylene Deposition

Design, Fabrication, and Characterization of A Polymer-Based Mems Uncooled Infrared Focal Plane Array

Study of In-Situ Measurement System for Porous Alumina Film Based on AFM and Reflectometric Interference Spectroscopy

Fabrication And Characterization Of Parylene C-Caulked Pdms For Low-Permeable Microfluidics

Structural Investigation And Barrier Properties Of A-C : H Thin Films On Polymer By Pecvd

Wafer Bonding with Intermediate Parylene Layer

Optimized chemical mechanical polishing of Parylene C for high-density wiring in flexible electronics

SF6 Optimized O2 Plasma Etching of Parylene C