Abstract:Nickel-based superalloys are subject to severe microsegregation and exhibit anisotropic properties during laser metal deposition (LMD), which restricts their wide application in the aerospace field. Thus, post heat-treatments must be investigated to further regulate the microstructure and mechanical properties of such components. The aim is to provide a comprehensive understanding of the effects of double-stage aging (DA) and solution plus double-stage aging (SDA) heat treatments on microstructure and mechanical properties of Hastelloy X superalloy sheets fabricated via LMD. The effects of DA and SDA heat treatments on the density, residual stress, phase composition, carbides precipitation behavior, dislocation structure, grain structure, and mechanical properties of the sheets were studied and in comparison with the as-deposited (AD) samples. The results showed that the DA heat treatment yielded a significant amount of lamellar and granular phases in the interdendrites and grain boundaries, whereas the anisotropic microstructure between the transverse and vertical planes was similar to that observed in the AD samples. These phases are mainly composed of Laves phase and carbides. However, the needle-like carbide phase was dispersedly precipitated within the grains and at grain boundaries, and exhibited full recrystallization and reduced dislocation density after SDA heat treatment. Consequently, the SDA samples presented superior strength-ductility balance to those of the AD and DA samples with irregularly shaped Laves phase and carbides owing to microstructural changes. For instance, the SDA heat treatment improved the ultimate tensile strength and fracture elongation of the vertical samples by up to 10.9% and 30.7%, respectively, whereas the microhardness decreased by 13.3% compared to the AD samples. The compressive residual stress of 98 MPa and tensile residual stress of 147 MPa were also observed on the surfaces of the SDA and AD samples, respectively. In addition, the SDA samples exhibited an almost isotropic tensile behavior in the vertical and horizontal directions as the epitaxially grown columnar grains transforms into equiaxed grains, as well as exhibited a prominent overall crystallographic texture. The effect of DA and SDA heat treatments on the mechanical properties were analyzed on the basis of stress–strain curves, hardening behavior, and multiple strengthening mechanisms.

Evaluation of the ATI 718plus Repaired by Laser Metal Deposition under Heat Treatment Regimes: Microstructures, Mechanical Properties, and Their Heterogeneity

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Mechanical Performance of Laser Deposition Repairing of in 738 on Directionally Solidified Superalloy Blade

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Improved mechanical properties of laser-repaired 15-5PH stainless steel by in-situ heat treatment and grain refinement

Effect of heat treatment on microstructure, precipitation behavior and mechanical properties of Inconel 718 fabricated by laser direct energy deposition

Distribution of Microstructure, Elastic Modulus and Residual Stress Near the Interface in Laser Repaired GH4169 Superalloy

Tailoring the microstructure and mechanical properties of laser metal-deposited Hastelloy X superalloy sheets via post heat-treatment

Effect of thermal cycles on laser direct energy deposition repair performance of nickel-based superalloy: Microstructure and tensile properties

Effect of heat treatment on microstructure and mechanical properties of selective laser melted Inconel 718 alloy

Laser directed energy deposition remanufacturing of LPBF-processed TA15 parts: Hybrid process interface induced microstructure inheritance and mechanical performance

Aging Hardening Behavior and P Texture Formation of Laser Repaired GH4169 Nickel-Based Alloy

TLP repaired IN738LC superalloy with uneven surface defect gap width after post heat treatment: Microstructure and mechanical properties

On the Microstructure, Residual Stress and Fatigue Performance of Laser Metal Deposited TC17 Alloy Subjected to Laser Shock Peening

Effect of Ultrasonic‐Assisted Treatment on Microstructure and Mechanical Properties of Laser Deposition Repairing AlSi7Mg Alloy

Microstructures and mechanical properties of Ti6Al4V alloy repaired by the technology of point-mode forging and laser repairing

Rolling-assisted direct energy deposited Inconel 718: Microstructural evolution and mechanical properties after optimized heat treatment

Effect of heat treatment on microstructures and mechanical properties of Inconel 718 additively manufactured using gradient laser power

Microstructural evolution and tensile property enhancement of remanufactured Ti6Al4V using hybrid manufacturing of laser directed energy deposition with laser shock peening