Abstract:Wire-based laser directed energy deposition (LDED) technology is an attractive and efficient additive manufacturing technology, which shows great potential in the process of manufacturing high-value engineering components. However, the thermal effect will lead to a large amount of residual tensile stress in the components, and the large crystal structures after solidification seriously affects the tensile performance. The pursuit of high mechanical properties in additive manufacturing components have prompted researchers to seek new strengthening process to produce high-strength components. Therefore, in this paper, laser shock peening (LSP) composite wire-based LDED were used for the additive manufacturing of 17-4 PH stainless steel under the specified experimental conditions, and the effects of LSP on microstructure evolution, microhardness, and tensile properties of wire-based LDED components were systematically studied. Results showed that uniform grains with an average size of 2.31 mu m were generated on the top surface of specimen due to the ultra-high plastic strain induced by LSP shock wave. The size of hierarchical martensitic units shows varying degrees of reduction after LSP treatment, which is shown by the width decrease of packet, block and lath. Dynamic recrystallization caused by rearrangement and annihilation of high-density dislocations promoted the grain refinement. Meanwhile, the residual stress was completely converted from tensile state into compressive state with a maximum value of 425 MPa, and the microhardness was also enhanced to a peak value of 432 HV. In addition, we observed that the high-density dislocation environment created by LSP treatment promoted the further precipitation, and the aggregation phenomenon of precipitates was observed in the dense dislocation area. Furthermore, the tensile strength and elongation of LSP treated specimen were improved significantly, which was attributed to the combined effects of grain refinement, introduction of dislocation structures, precipitation strengthening and gradient residual compressive stress. In summary, laser hybrid additive manufacturing technology provides a new idea and method for the production of high-performance precipitation hardening stainless steel components.

Microstructural evolution and tensile property enhancement of remanufactured Ti6Al4V using hybrid manufacturing of laser directed energy deposition with laser shock peening

High-performance integrated additive manufacturing with laser shock peening –induced microstructural evolution and improvement in mechanical properties of Ti6Al4V alloy components

Achieving high strength and ductility in selective laser melting Ti-6Al-4V alloy by laser shock peening

Laser directed energy deposition remanufacturing of LPBF-processed TA15 parts: Hybrid process interface induced microstructure inheritance and mechanical performance

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

On the Microstructure, Residual Stress and Fatigue Performance of Laser Metal Deposited TC17 Alloy Subjected to Laser Shock Peening

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Laser shock peened Ti-6Al-4 V alloy: Experiments and modeling

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Effects of Conventional Interweaving and Secondary Deposition on the Microstructure and Properties of Ti6Al4V/AA2024 Alloy Component Fabricated by Laser-Directed Energy Deposition

Microstructure and fracture behavior of 90W-7Ni-3Fe alloy fabricated by laser directed energy deposition

Tailoring microstructure of additively manufactured Ti6Al4V titanium alloy using hybrid additive manufacturing technology

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Effects of Laser Shock Peening on Microstructure and Properties of Ti–6Al–4V Titanium Alloy Fabricated via Selective Laser Melting

Effects of Laser Rescanning on Microstructure and Mechanical Properties of Al-10Si-1Mg Alloy Produced by Laser-Directed Energy Deposition

Tensile Properties and Microstructural Evolution of 17–4 PH Stainless Steel Fabricated by Laser Hybrid Additive Manufacturing Technology

Fundamental Study of In-Situ Strengthening and Formation of Continuous Gradient Titanium Alloys via Laser Directed Energy Deposition

Effects of laser printing parameters on molten pool formation, microstructure evolution and mechanical properties of laser directed energy deposition of difficult-to-process tungsten heavy-alloy

Gradient microstructure and foreign-object-damaged fatigue properties of Ti6Al4V titanium alloy processed by the laser shock peening and subsequent shot peening