Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

Fundamental Study of In-Situ Strengthening and Formation of Continuous Gradient Titanium Alloys via Laser Directed Energy Deposition

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

In-situ additive manufacturing of high strength yet ductility titanium composites with gradient layered structure using N2

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-situ synthesis of spatial heterostructure Ti composites by laser powder bed fusion to overcome the strength and plasticity trade-off

In-situ synthesis of high strength and toughness TiN/Ti6Al4V sandwich composites by laser powder bed fusion under a nitrogen-containing atmosphere

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

Synergistic Strengthening Mechanisms of Dual-Phase (TiN+AlN) Reinforced Aluminum Matrix Composites Prepared by Laser Powder Bed Fusion

Formability, densification behavior and hierarchical grain structure of laser-directed energy deposition of TiB reinforced titanium matrix composites

Microstructural evolution and tensile property enhancement of remanufactured Ti6Al4V using hybrid manufacturing of laser directed energy deposition with laser shock peening

Microstructure evolution and strengthening mechanisms of a high-performance TiN-reinforced Al-Mn-Mg-Sc-Zr alloy processed by laser powder bed fusion

Combined Strengthening of Multi-Phase and Graded Interface in Laser Additive Manufactured Tic/Inconel 718 Composites

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

Fabrication of heterostructured Ti alloys with exceptional strength and ductility by direct laser deposition

Strengthening layer with nano-twins in titanium alloy induced by laser surface re-melting: Mechanism of high strength and ductility

Integrated laser additive manufacturing of high-strength steel and Ti6Al4V: Experimental investigations and thermodynamic calculations

Multilayered Gradient Titanium-Matrix Composites Fabricated by Multi-Material Laser Powder Bed Fusion Using Metallized Ceramic: Forming Characteristics, Microstructure Evolution, and Multifunctional Properties

Strength-ductility synergy in 3D-printed (TiB + TiC)/Ti6Al4V composites with unique dual-heterogeneous structure

Microstructure and mechanical properties of Ti60–Ti 2 AlNb functionally graded materials fabricated by laser directed energy deposition

Microstructure evolution and reaction mechanism of continuously compositionally Ti/Al intermetallic graded material fabricated by laser powder deposition

Achieving strength-ductility combination and anisotropy elimination in additively manufactured TiB/Ti6Al4V by in-situ synthesized network architecture with fine grains