Abstract:To scientific understanding the effect of a slight change in carbon content near the upper/lower limit on alloys, five sets of WC-10Co cemented carbides were prepared with the carbon content of 5.34 wt%, 5.36 wt%, 5.44 wt %, 5.53 wt% and 5.56 wt% respectively. The properties of the alloys are analyzed by SEM, XRD, Hardness tester, universal testing machines, HSR-2 M tribometer, and surface characterisation. The results showed that the existent of multi-steps proved that the WC coarsening process was governed by 2-D nucleation in the alloy with low carbon content. On the contrary, the low W solubility in Co and the low melting point of Co binder accelerated the dissolution-precipitation process with increasing carbon content. At this time, the morphologies of WC grains tented to be the triangular shape without multi-steps due to the continuous grain growth. Additionally, the increasing of the value of carbon content brought about the coarser WC grain size, and the particle size distribution with ?double peak? was also observed in the alloy with free carbon. Further analysis of XRD, the various dissolution of W in Co binder phase brought about a minor different intensity of the basal plane (0001) peaks. Moreover, a slight change in carbon content near the upper/lower limit also significantly affected the mechanical properties of alloys. The cemented carbides with 5.44 wt% carbon content in two phase range exhibited a combination of superior mechanical properties and wear resistance.

Effect of WO3 Content on Microstructure and Properties of Ultracoarse Grained Cemented Carbide

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of carbon content on the properties of inhomogeneous cemented carbides with fine-grained structures produced via one-step transformation

Effect of Carbon Content on Microstructure and Mechanical Properties of WC-10Co Cemented Carbides with Plate-Like WC Grain

Effect of Carbon Content on the Microstructure and Mechanical Properties of Ultrafine WC-15Co Cemented Carbides Using a Co-based Solid Solution Binder Phase

Effect of coarse grained WC addition on microstructure and mechanical properties of WC-Co cemented carbide

Effect of a Slight Change in Carbon Content Near the Upper/lower Limit on the Microstructure and Mechanical Properties of WC-10Co Cemented Carbides

Influence of VC/Cr3C2 and Mixed Carbon Content on Microstructure and Properties of Ultrafine WC-0.5Co Cemented Carbide

Effect of Cobalt Content on the Microstructure and Mechanical Properties of Coarse Grained WC-Co Cemented Carbides Fabricated from Chemically Coated Composite Powder

Research on Microstructure and Properties of Ultrafine Grained WC-Ni3Al Cemented Carbide

Effect of WO3 content on microstructure and mechanical properties of dual-grain structured hardmetals fabricated by in-situ carbothermal reduction of WO3

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

Microstructure Evolution in the Cemented Carbides Wc-Coi. Effect of the C/W Ratio on the Morphology and Defects of the Wc Grains

Effect of (cr, V)2(C, N) on the Microstructure and Mechanical Properties of WC-10Co Cemented Carbides

Microstructure and Mechanical Properties of Ultra-Fine WC-10Co Cemented Carbides with Cr3C2 and NbC: Experimental Investigation Supported by Thermodynamic Calculation

The Enhancement of the Microstructure and Mechanical Performances of Ultrafine WC-Co Cemented Carbides by Optimizing Cr2(C,N) Addition and WC Particle Sizes

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

The influence of different content of Cr on microstructure and properties of WC-Co cemented carbide

Fabrication and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Effect of Y2O3 on microstructure and mechanical properties of WC-Co-cemented carbides prepared via solid-liquid doping method and spark plasma sintering

Effect of Carbon Content on the Microstructure and Properties of WC-CoCrFeNi Cemented Carbides